User manual KONICA MINOLTA MAGICOLOR 2 CX Reference Guide

[. . . ] QMS magicolor CX Reference Guide ® ® 1800428-001B Trademarks The following are trademarks or registered trademarks of their respective owners. Other product names mentioned in this manual may also be trademarks or registered trademarks of their respective owners. Registered trademarks are registered in the United States Patent and Trademark Office; some trademarks may also be registered in other countries. QMS, magicolor, and the QMS logo are registered trademarks of QMS, Inc. , and Crown, the Crown seal, and PS Executive Series are trademarks of QMS, Inc. [. . . ] (You may need to use your fingers to open these clips. ) When seated, the SIMM stands upright, firmly in place. J1 J2 v Caution: If you cannot easily fit the SIMM into place, do not force it. Reposition it, making sure that the bottom of the SIMM is seated completely in the connector. 5 6 Repeat step 4 to install the other SIMM in the remaining connector (J1). Follow the instructions in "Replacing the Controller Board" on page 21, being careful to follow the directions for eliminating electrostatic buildup. Printer Options 2-25 The Intellifont SIMM The Intellifont SIMM » Note: If you're installing a RAM SIMM, see "Single In-Line Memory Modules (SIMMs)" on page 23 for instructions. Intellifont SIMM and RAM SIMM connectors are not interchangeable. An optional Intellifont SIMM increases the number of fonts available to the HP PCL 5 emulation on your printer from 20 to the 37 PCL 5 fonts available on a Hewlett-Packard LaserJet 4Si. M WARNING!Turn off the printer and unplug the power cord before taking the cover off the printer. Bitte schalten Sie den Drucker aus und ziehen Sie den Netzstecker heraus bevor Sie die Druckerabdeckung öffnen. v Caution: It's very important to protect the printer tray assembly from electrostatic damage while performing this task. If an anti-static wrist strap is provided in your printer option kit, attach one end of it to your wrist and the other end to any convenient electrical ground (for example, the bare metal chassis of equipment, as on the back of a computer, that is plugged in but turned off). Never attach the wrist strap to any piece of equipment with an electrical current present. Plastic, rubber, wood, painted metal surfaces, and telephones are not acceptable grounding points. The printer isn't an acceptable grounding point either because it must be unplugged before you perform this task. If you don't have an anti-static wrist strap, discharge your body's static electric charge by touching a grounded surface before you handle any printer boards or components and before removing the tray assembly cover. Redischarge your body each time after walking around and before touching the printer tray assembly again. 1 Follow the instructions in "Removing the Controller Board" on page 20, being careful to discharge electrostatic buildup before you begin. 2-26 QMS magicolor CX Reference Guide The Intellifont SIMM 2 Turn the controller board so that the Intellifont SIMM slot is on the side to you. Intellifont SIMM slot 3 Insert the SIMM into the connector. Position the SIMM at a 60° angle to the controller board, with the notch on the left side and the bottom edge in the connector. Then push the SIMM forward until you feel it fit into place behind the clips on either side of the connector. (You may need to use your fingers to open these clips. ) When seated, the SIMM stands at an angle, firmly in place. ° angle Printer Options 2-27 The Intellifont SIMM 4 Follow the instructions in "Replacing the Controller Board" on page 21, being careful to follow the directions for eliminating electrostatic buildup. Increasing the Disk Cache Size If your printer has 8 MB of RAM total, you must set the disk cache to a minimum of 48 KB (Administration/Memory/Disk Cache menu) to use the Intellifont SIMM. » Note: You may need to decrease one of the other memory clients before increasing the disk cache client, or add more memory. If your printer has more than 8 MB RAM, the size of the disk cache is automatically adjusted. Verifying the Installation Once you have installed the Intellifont SIMM, print a start-up page and an advanced status page to verify the installation. 1 2 3 Wait for the printer message window to display IDLE. If necessary, use the Administration/Startup Options/Startup Page menu to enable start-up pages. In the Options section of the start-up page, a new option identified as %cartridge2% verifies the installation of the SIMM. 4 5 Use the Administration/Special Pages/Status Page Type menu to change the default Standard setting to Advanced. [. . . ] For example, when the printer is set for PostScript Level 2 emulation, it responds to the same commands that a PostScript Level 2 printer does. Engine The non-intelligent part of a printer where the paper is physically processed and printed. ESP Technology Emulation Sensing Processor Technology: technology that uses a form of artificial intelligence to analyze incoming file data from any of the printer's interfaces. ESP technology, which works with most popular commercially available applications, selects the appropriate printer emulation from those installed on the printer and processes the print job, freeing the user from having to change printer switch settings or send software commands to accommodate different printer emulations. ESP mode is an option for the printer's serial, and parallel interfaces. Factory Default The printer settings that are programmed into the printer at the factory. These settings can be changed through the printer control panel or overridden with printer commands sent through software. [. . . ]