User manual KONICA MINOLTA MAGICOLOR 2 DESKLASER Installation Guide

[. . . ] » Note: Save the packing material for possible repacking. Remove the protective plastic covering the printer. With another person's help, lift the printer from the base tray, and place it in its permanent location. When lifting and carrying the printer, use the carrying grips on the bottom sides. &DUU\LQJ *ULSV &DUU\LQJ *ULSV 2 Check the shipment contents; if any items are missing or damaged, contact your shipping company or your local vendor: Printer 250-sheet letter/A4 standard media cassette Consumables starter kit (4 starter toner cartridges, OPC belt cartridge, fuser oil bottle/cleaning roller/oil removal syringe) Power cord magicolor 2 DeskLaser Installation Guide (this handout), magicolor 2 DeskLaser Setup Guide, magicolor 2 DeskLaser Documentation and Software CD-ROM · Warranty and registration card » Note: Interface cables aren't included in the shipment. If you need cables, contact your local vendor or computer store. [. . . ] Align the toner cartridge with the cartridge guides, and gently push the cartridge into the printer until you begin to feel resistance. Then pull the cartridge back approximately 1/4 inch. 7DE 3 While the cartridges may appear not to be fully inserted, gently closing the front cover will guide them to their proper operating position. Each toner cartridge has a colored label that corresponds to a colored label to the right of the cartridge slots. Always install the toner cartridge in the slot with a label of the same color. Install the other toner cartridges. &RORUHG /DEHOV 2 magicolor 2 DeskLaser or DeskLaser Duplex Model (continued) D. Installing the OPC Belt Cartridge < Caution: The OPC belt is extremely sensitive to bright light and touch. Always leave it in its protective bag until you are ready to install it. Any exposure to light should be limited to less than two minutes or permanent damage could result. Always handle the cartridge so you don't touch the surface of the belt. 1 Rotate up the two lock levers to prepare the opening for the cartridge. < Caution: Make sure the printer's front cover is still open. This makes room for the OPC belt cartridge. 2 Pull out the two tensionrelease pins (one on each side of the cartridge). Remove the protective sheet from the cartridge. » Note: The white powder lubricant on a new OPC belt is normal; it won't affect quality. 3 Holding the OPC belt cartridge above the printer, align the guide pins on the cartridge with the guide slots in the lock levers. The white gear on the cartridge goes to the right, and the green surface of the cartridge faces you. Gently guide the cartridge into the printer. 4 Rotate the two lock levers to secure the OPC belt cartridge. E. Installing the Fuser Oil Bottle and Cleaning Roller 1 Open the two cleaning roller lock levers by rotating them toward you. 2 Install the cleaning roller in its slot. The larger tab on the top of the cleaning roller must be on the left. &OHDQLQJ 5ROOHU 7DE 3 Lower the oil bottle into its slot. The tab on the side of the bottle must be on the right. » Note: Because the first oil bottle must prime the printer, it has less than the normal 12, 000-page (1-sided) life expectancy. 4 Close the two lock levers by rotating them away from you. Close the printer's top and front covers. If you have a duplex model, close the duplexer's rear cover. %RWWOH 7DE F. Loading the Media Cassette 1 Adjust the media guides to fit the size paper you're loading. Squeeze the retainers at the ends of the left width guide and/or the length guide, move the guide to the appropriate location (media sizes are listed on the cassette). [. . . ] Connecting Interface and Power Cables 1 Refer to the User's Guide for instructions on how to connect your printer to a computer or network. (WKHUQHW 3RUW 2 Plug the printer into a grounded, surge-protected electrical outlet. » Note: In compliance with UL guidelines, "The appliance inlet is considered to be the main disconnect device. " 3DUDOOHO 3RUW I. Configuring the Printer 1 See the User's Guide for instructions on installing the MINOLTA-QMS printer driver. Use the online help to configure the driver for printing. 2 Idle Installation Operator Use Operator Admin Use Admin Operator Control (Enter password) Off, On (Enter password) Off, On Administration See the User's Guide for further instructions on advanced printer configuration through the control panel menus. Registering the Printer Further Assistance Refer to one of the following: · · Chapter 8, "Troubleshooting Printer Problems, " in the magicolor 2 DeskLaser User's Guide on the magicolor 2 DeskLaser Documentation and Software CD-ROM. [. . . ]