User manual KONICA MINOLTA PI1802E UM 1.0.0

[. . . ] 4506-7732-01 User Manual Printer Controller Pi1802e Foreword Trademark Acknowledgements Minolta is a registered trademark of MINOLTA CO. , LTD. Ethernet is a registered trademark of Xerox Corporation. Microsoft, Windows, and Windows NT are registered trademarks of Microsoft Corporation. Netscape Communications, the Netscape Communications logo, Netscape Navigator, Netscape Communicator, and Netscape are trademarks of Netscape Communications Corporation. [. . . ] Insert one sheet of paper into the manual bypass tray of the Digital Copier. Paper loaded into the manual bypass tray is printed on. 3. Note · Be sure to execute the print operation from the computer, then load the paper into the manual bypass tray. If the paper has already been loaded, pull it out, and then insert it again. · Load the paper into the manual bypass tray one sheet at a time. · If the multiple bypass tray (optional) is installed, printing from it can be performed in the same way as with any other paper tray since the multiple bypass tray can hold 50 sheets of paper. · When using a custom size specified with the printer driver, be sure to set that size first with the Digital Copier. 29 5 Digital Copier Control Panel Operations (PC Print Mode) 5. 1. 5 Outputting a Report When the printer controller is installed, the following reports can be outputted. · Configuration Page · PCL Font List To Print the Configuration Page 1. Hold down the [Panel Reset] key for 3 seconds. "U--" appears in the display. 2. Press the [6] key from the 10-Key Pad. 3. Press the [Start] key. "L--" appears in the display. 4. Press the [1] key from the 10-Key Pad. 5. Press the [Start] key. The Configuration Page will be printed. Note · During the few minutes after the Digital Copier is turned on, "U-6" may not appear and an error may be displayed. 30 5 Digital Copier Control Panel Operations (PC Print Mode) To Print the PCL Font List 1. Hold down the [Panel Reset] key for 3 seconds. "U--" appears in the display. 2. Press the [6] key from the 10-Key Pad. 3. Press the [Start] key. "L--" appears in the display. 4. Press the [2] key from the 10-Key Pad. 5. Press the [Start] key. The PCL Font List will be printed. Note · During the few minutes after the Digital Copier is turned on, "U-6" may not appear and an error may be displayed. 31 5 Digital Copier Control Panel Operations (PC Print Mode) 5. 2 Operation Using the Di152f/Di183f When the print operation is executed from the computer, printing can begin without the mode of the Digital Copier changing. In Copy Mode Printing begins 30 seconds after the copy operation is finished. In addition, if the [Printer] key in the control panel is pressed, the Digital Copier switches to PC Print mode and printing begins. (For details about PC Print mode, refer to "5. 2. 3 Switching to PC Print Mode" on page 34. ) In Fax Mode Printing can also be performed while the Digital Copier is in Fax mode. However, if a received fax is being printed, PC print data will be printed after the Digital Copier has finished printing the fax. Whether in Copy mode or in Fax mode, the [Printer] indicator shows the current print status. In PC Print mode, the print job can be cancelled. 32 5 Digital Copier Control Panel Operations (PC Print Mode) 5. 2. 1 Names of Control Panel Parts and Their Functions 1 2 5 3 4 No. 1 2 3 Part Name [Printer] indicator [Printer] key [Start] key Function Displays the PC print status. Refer to "5. 2. 2 [Printer] Indicator/[Start] Key" on page 34. Refer to "5. 2. 3 Switching to PC Print Mode" on page 34. Lights up in orange to indicate that the Digital Copier is in PC Print mode. [. . . ] To print on the type of paper specified with the Digital Copier, press the [Start] key to begin printing. Remove the paper from the Upper Copy Tray or the Lower Copy Tray of the Job Tray, and then press any key on the operation panel. TRAY MOVEMENT ERROR (Flashing alternately) PRESS ANY KEY 59 9 Appendix 9 Appendix 9. 1 Assigning IP Parameters Using BOOTP BOOTP is a utility for assigning IP parameters to a Network Interface Card (NIC). When BOOTP is run on a computer, a BOOTP request from a NIC causes IP parameters that match the MAC address of the NIC to be assigned to the NIC. Requirements · Computer must have TCP/IP installed and enabled. · NIC must be connected to the same subnetwork as the computer running BOOTP. [. . . ]