User manual KONICA MINOLTA PI1802E UM 2.1.0

[. . . ] User Manual Pi1802e www. minoltaeurope. com The essentials of imaging Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . X-1 Trademark Acknowledgements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Users . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . X-2 For Canada Users . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Regardless of the mode, the message shown at the right appears in the display of the Digital Copier. 3 Insert one sheet of paper into the manual bypass tray of the Digital Copier. Paper loaded into the manual bypass tray is printed on. Pi1802e 5-13 5 Digital Copier Control Panel Operations (PC Print Mode) NOTE è Be sure to execute the print operation from the computer, then load the paper into the manual bypass tray. If the paper has already been loaded, pull it out, and then insert it again. Load the paper into the manual bypass tray one sheet at a time. If the multiple bypass tray (optional) is installed, printing from it can be performed in the same way as with any other paper tray since the multiple bypass tray can hold 50 sheets of paper. When using a custom size specified with the printer driver, be sure to set that size first with the Digital Copier. è è è 5-14 Pi1802e Digital Copier Control Panel Operations (PC Print Mode) Outputting a Report When the printer controller is installed, the following reports can be outputted. l Configuration Page l PCL Font List 5 1 Press the [Confirm] key 3 times. A confirmation message appears, asking whether or not to print a report. 2 Press the [Yes] key. A menu appears, showing the reports and lists that can be printed. 3 Using the and keys, select the report/list that you wish to print, and then press the [Yes] key. m m Configuration Page PCL Font List After the specified report/list is printed, the main screen appears again. NOTE è If the Digital Copier was just turned on, it may take a few minutes before the menu is displayed. Pi1802e 5-15 5 Digital Copier Control Panel Operations (PC Print Mode) 5-16 Pi1802e Digital Copier Settings for Use on a Network 6 6 Digital Copier Settings for Use on a Network NOTE è If the Digital Copier is to be used as a printer on a network, the optional network interface card NC-3 must be installed. The network settings can only be specified when the network interface card is installed. The following network settings can be specified from the Digital Copier. l IP address l Subnet mask l Default gateway NOTE è Network settings other than those listed above can be specified with the enclosed PageScope Light. For details, refer to the PageScope Light for Pi1802e User Manual. If the IP address, subnet mask and default gateway are specified using the Digital Copier, they can later be changed using PageScope Light. The network settings should be specified according to instructions from the network administrator. è è The control panel operations differ according to the functions of the Digital Copier. Refer to the page corresponding to the model being used. l Di152/Di183 Di152f/Di183f, or Di152/Di183 with the fax unit installed "6. 1 Specifying Settings Using the Di152/Di183" on page 6-2 "6. 2 Specifying Settings Using the Di152f/Di183f" on page 6-8 l Pi1802e 6-1 6 6. 1 IP Address Digital Copier Settings for Use on a Network Specifying Settings Using the Di152/Di183 1 Hold down the [Panel Reset] key for 3 seconds. "U--" appears in the display. 2 Press the [6] key from the 10-Key Pad. 3 Press the [Start] key. "L--" appears in the display. 4 5 Press the [3] key from the 10-Key Pad. Press the [Start] key. 6-2 Pi1802e Digital Copier Settings for Use on a Network 6 6 The procedure differs depending on whether the IP address is automatically assigned or a fixed IP address is entered. m m Assign automatically (1): Perform this procedure if there is a DHCP (Dynamic Host Configuration Protocol) server on the network and the IP address is automatically assigned by the server. Fixed IP address (2): Perform this procedure when assigning a fixed IP address for the printer controller. To assign the IP address automatically, press the [Clear] key, Press the [1] key and then press the [Start] key. "Aut" appears in the display for two seconds, and then "U--" appears. With this procedure, it is not necessary to set the subnet mask and gateway. [. . . ] Print Server Password/Password Retype Type in the password here when a password is defined on the print server registered in the NetWare file server. Type the same password into the "Password Retype" field for confirmation. Preferred File Server Type in the name of the preferred file server when setting up for bindery and bindery emulation. The print server must always be configured on a preferred file server. [. . . ]