User manual KONICA MINOLTA PI4700 UM 1.1.0

[. . . ] User Manual Pi4700e www. minoltaeurope. com The essentials of imaging Table of Contents Welcome . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . X-5 Trademark Acknowledgements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . X-5 Limited Software Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . X-6 Minolta Network Card Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] 15 Enter the printer settings, and then click the Apply Changes button. If you have problems during the installation, please refer to the Advanced User Manual on the CD. Pi4700e 2-15 2 Installing the Printer Driver 2-16 Pi4700e Network Settings 3 3 3. 1 Network Settings Introduction Though this Network Card does not support NetBEUI protocol, it supports TCP/IP and IPX/SPX, which provides plenty of connection flexibility for the Windows computer. A Windows 95/98/Me network printer can be used by going through a Novell NetWare or Windows 2000/NT server. This Network Card, however, can be configured with its bundled peer-to-peer printing programs for peer-to-peer printing without a server. Peer-to-peer printing can be performed using TCP/IP or IPX/SPX. There are two ways you can print from Windows NT 4. 0 with TCP/IP: using the bundled IP Peer-to-Peer Printing Program, and using the Windows NT standard LPR printing function. There are two ways you can print from Windows 2000/XP with TCP/IP: using the Windows 2000/XP standard LPR printing function, and using the Windows 2000/XP standard IPP printing function. Pi4700e 3-1 3 3. 2 Network Settings Specifying the IP Address From the Printer's Touch Panel Setting procedure 1 Press the [Utility] key. 2 Touch [Administrator Mode] and input the Administrator code. 3 Touch [NetworkSet]. 4 Touch [IP Address]. 3-2 Pi4700e Network Settings 3 5 With the keypad in the operation panel, type in the IP address, and then touch [Enter]. 6 With the keypad in the operation panel, type in the subnet mask, and then touch [Enter]. 7 With the keypad in the operation panel, type in the default gateway, and then touch [Enter]. Pi4700e 3-3 3 again. Network Settings 8 In order to activate the address settings, turn the printer off, then on 3-4 Pi4700e Network Settings 3 3. 3 Peer-to-Peer Printing with TCP/IP Use the bundled IP Peer-to-Peer Printing Program for TCP/IP peer-topeer printing under Windows. Digital Copier Network Card TCP/IP Windows TCP/IP IP Peer to Peer Printing Program NOTE è Refer to the Advanced User Manual on the controller CD-ROM for details. Peer-to-Peer Printing Program is a Windows utility that lets you output directly to a printer from a computer on a network, without going through a server. Use this program for peer-to-peer printing under TCP/IP. Requirements l Computer must have TCP/IP installed and enabled. l Network Card must have valid IP parameters assigned. NOTE è è Refer to the applicable Windows documentation for information about installing TCP/IP under Windows. Refer to the Advanced User Manual on the controller CD-ROM for Pi4700e 3-5 3 details. Network Settings 3. 4 Peer-to-Peer Printing with IPX/SPX Use the bundled IPX Peer-to-Peer Printing Program for IPX/SPX peer-topeer printing under Windows. With IPX Peer-to-Peer Printing Program, there is no need to run NetWare Client. Digital Copier Network Card IPX/SPX Windows 95/98/Me IPX/SPX-compatible Protocol IPX Peer to Peer Printing Program NOTE è Refer to the Advanced User Manual on the controller CD-ROM for details. Use this program for peer-to-peer printing under IPX/SPX. Just by installing this program, you can specify an IPX-based printer on the network as a printer port. Requirements l Computer must have IPX/SPX-compatible protocol installed. NOTE è Refer to the applicable Windows documentation for information Pi4700e 3-6 Network Settings about installing IPX/SPX under Windows. è 3 Refer to the Advanced User Manual on the controller CD-ROM for details. 3. 5 LPR Printing This section explains how to use the Windows NT 4. 0/2000/XP standard LPR printing function. Digital Copier Network Card TCP/IP Windows NT 4. 0/2000/XP TCP/IP Microsoft TCP/IP Printing NOTE è Refer to the Advanced User Manual on the controller CD-ROM for details. Requirements l Computer must have TCP/IP installed and enabled. l Network Card must have valid IP parameters assigned. Pi4700e 3-7 3 3. 6 IPP Printing Network Settings This section explains how to use the Windows 2000/XP standard IPP printing function. Digital Copier Network Card IPP Windows 2000/XP TCP/IP IPP Client NOTE è Refer to the Advanced User Manual on the controller CD-ROM for details. Requirements l Computer must have TCP/IP installed and enabled. l Network Card must have valid IP parameters assigned. 3-8 Pi4700e Network Settings 3 3. 7 Specifying network settings from PageScope Light Access PageScope Light for Pi4700e can be accessed directly from a Web browser. 1 Start the Web browser. 2 In the URL field, enter the IP address of the printer controller as shown below. http://<IP address of printer controller>/ (Example) When the IP address of the printer controller is 192. 9. 200. 200: http://192. 9. 200. 200/ 3 This causes PageScope Light for Pi4700e screen to appear. Operation PageScope Light for Pi4700e operation is identical to that for Internet Web pages. Clicking a hot link jumps to the link destination, and the Back and Forward buttons scroll through pages backwards and forward. For further details of PageScope Light, please refer to the Advanced User Manual on the CD. Pi4700e 3-9 3 Logging In to the Admin Mode Network Settings After you log in to PageScope Light in the Admin Mode, you can change the configuration of the Digital Copier settings. 1 Type the administrator password into the Admin Password box. [. . . ] The paper direction and N-up do not match the setting made for Orientation. Action Troubleshooting Check the type of paper. Check the number of prints to be made. Change the setting for Orientation. Select "Multi-staple Finisher" "Mailbin Finisher" or "Folding Finisher" from "Installable Options. " Check the setting of Booklet and OHP Interleaving. Check the type of paper. Check the direction of the paper. Change the setting for Orientation. 8-4 Pi4700e Troubleshooting 8 Possible Cause (for Windows) The optional Folding Finisher is necessary for you to specify Folding. [. . . ]