User manual KORG 1212IO

[. . . ] Do not connect it to an AC outlet of voltage other than that for which your unit is intended. Interference with other electrical devices This product contains a microcomputer. Radios and televisions placed nearby may cause reception interference. Operate this unit at a suitable distance from radios and televisions. Handling To avoid breakage, do not apply excessive force to the switches or controls. Care If the exterior becomes dirty, wipe it with a clean, dry cloth. Do not use liquid cleaners such as benzene or thinner, cleaning compounds or flammable polishes. Keep this manual After reading this manual, please keep it for later reference. Keeping foreign matter out of your equipment • Never set any container with liquid in it near this equipment. [. . . ] As the knob is rotated toward the right, the effect sound will increase and the direct sound will decrease. Pitch Shifter This effect shifts the pitch. Edit 1 _ Pitch 0. . . 127 Specifies the amount of pitch shift. When the knob is in the center position, the output pitch will be the same as the input pitch. As the knob is rotated toward the left the pitch will become lower, and as the knob is rotated toward the right the pitch will become higher. The available range of pitch shift is +/-2 octaves, and will change as shown below. Pitch Offset Values Value 127 125 123 121 119 117 115 113 111 109 107 105 103 100 97 94 91 Step Value Step +12 (2 oct. up) 88 +3 1/2 +11 1/2 85 +3 +11 82 +2 1/2 +10 1/2 79 +2 +10 76 +1 1/2 +9 1/2 73 +1 +9 70 +1/2 +8 1/2 64 actual pitch +8 57 -1/2 +7 1/2 54 -1 +7 51 -1 1/2 +6 1/2 48 -2 +6 (1 oct. up) 45 -2 1/2 +5 1/2 42 -3 +5 39 -3 1/2 +4 1/2 36 -4 +4 33 -4 1/2 Value 30 27 24 22 20 18 16 14 12 10 8 6 4 2 0 Step -5 -5 1/2 -6 (1 oct. down) -6 1/2 -7 -7 1/2 -8 -8 1/2 -9 -9 1/2 -10 -10 1/2 -11 -11 1/2 -12 (2 oct. down) Effect types and parameters Motion Seq (motion sequence) This is the motion sequence for the effect (see p. 34 “Motion sequence”). Each time you press the key, this will alternate between on (lit) and off (dark). If the MIDI Clock setting is Ext (external), you can synchronize the delay time to the clock of an external device. (Refer to p. 46 “Synchronizing the EM-1 and an external MIDI devices ( MIDI Clock)”) Edit 2 _ Depth 0. . . 127 This adjusts the LFO depth and the feedback amount of the delay. Turning the knob toward the right will deepen the LFO and increase the amount of feedback. 30 ○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○ DELAY Delay is an effect that adds one or more delayed “echoes” to the sound. The delay effect of the EM-1 is a “cross-feedback delay. ” This feeds the delayed L and R signal back into the opposite side to produce a greater feeling of spaciousness from left to right. This delay is a tempo delay in which the delay time is automatically synchronized to the tempo of the pattern, and movements of the delay knob can also be recorded as a motion sequence. Left input Right input Delay Delay Left output Right output Press the delay edit key (the key will light) to enter Delay Edit. Use the two knobs (Time, Depth) to edit. The delay effect will apply to the entire pattern, and it is not possible to change the effect independently for each part. To edit the delay, you must make sure that the Delay Edit key is lit. If you move the effect type knob, you will return to effect edit. Slight noise may be heard when you change patterns, due to the change in delay time. Motion Seq (motion sequence) This is the delay motion sequence (see p. 34 “Motion sequence”). Each time you press the key, the setting will alternate between on (lit) and off (dark). Time (delay time) 0. . . 127 Set the delay time in synchronization with the tempo. [. . . ] If you attempt to record additional events, the "memory full" message will appear immediately. Please erase event data to free up memory (p. 45). Restoring the factory set data The pattern and song data with which the EM-1 is shipped from the factory is referred to as the "preloaded data, " and you can restore this preloaded data back into the memory of the EM-1. When you do this, the patterns you created and the songs which use these patterns will be erased, and replaced by the preloaded data. If you wish to keep the patterns and songs you created, you must save the data on a data filer etc. [. . . ]