User manual KORG AX3000B 1

[. . . ] E 1 Precautions Location Using the unit in the following locations can result in a malfunction. · In direct sunlight · Locations of extreme temperature or humidity · Excessively dusty or dirty locations · Locations of excessive vibration · Close to magnetic fields Power supply Please connect the designated AC adapter to an AC outlet of the correct voltage. Do not connect it to an AC outlet of voltage other than that for which your unit is intended. Interference with other electrical devices Radios and televisions placed nearby may experience reception interference. Operate this unit at a suitable distance from radios and televisions. Handling To avoid breakage, do not apply excessive force to the switches or controls. Care If the exterior becomes dirty, wipe it with a clean, dry cloth. [. . . ] [1] "DEPTH" [2] "SPEED" [3] "MANUAL" 0. 0­10. 0 0. 1­10. 0[Hz] 1. 0­10. 0 * Adjusts the modulation depth. * Adjusts the center frequency of the sweep. If DEPTH is set to 10, MANUAL will not function. Stereo mode in which the effect is panned right, and the dry sound panned left. Vibrato mode, in which only the effected sound is output. Setting MANUAL to 10 will minimize the delay of the output. [5] "MODE" 1: 2: 3: 30 2. MULTI TAP CHORUS (MT CHORS) This is a chorus with independent taps for left/center/right, adding depth and spaciousness to your sound. [1] [2] [3] [5] "DEPTH" "SPEED" "TIME" "MIX" 0. 0­10. 0 0. 1­10. 0[Hz] 0. 0­10. 0 0. 0­10. 0 * Adjusts the modulation depth. * Adjusts the mix level of the effect. 3. CLASSIC FLANGER (CL FLANG) This models a classic analog flanger. [1] "DEPTH" [2] "SPEED" [3] "MANUAL" 0. 0­10. 0 0. 1­10. 0[Hz] 1. 0­10. 0 * Adjusts the modulation depth. * Adjusts the center frequency of the sweep. If DEPTH is set to 10, MANUAL will not function. If you set the FLN TRIG: CONTROL switch setting to "FLN TRIG, " the LFO will be reset to the position specified by OFFSET whenever you operate the switch. BI CHORUS (BI CHORS) This is a chorus model unique to the AX3000B. It provides two chorus units, CHORUS 1 and CHORUS 2, and lets you connect the two units not only in series or in parallel, but also to synchronize or de-synchronize the two LFOs. It produces a variety of tones that cover a range from wonderfully spacious sounds to bizarre flanger-like sounds with complex modulation. [1] "DEPTH" 0. 0­10. 0 [2] "SPEED 1" 0. 1­10. 0[Hz] [3] "SPEED 2" 0. 1­10. 0[Hz] * Adjusts the modulation depth of CHORUS 1/2. * Adjusts the modulation speed of CHORUS 1. * Adjusts the modulation speed of CHORUS 2. NOTE: This will not function if MODE is set to P2 or P3. [5] "MODE" S: P1: P2: 31 REVERB DELAY [4] "RESO" 0. 0­10. 0 * Adjusts the amount of resonance for CHORUS 1/2. Specifies the connection and LFO for CHORUS 1/2. CHORUS 1/2 are connected in parallel, and their LFOs are synchronized. MODULATION PRE EFFECT CABINET DRIVE/AMP Effect Type [4] "RESO" 0. 0­10. 0 [5] "MIX" 0. 0­10. 0 CONTROL switch FLN TRIG Tuner P3: CHORUS 1/2 are connected in parallel, and their LFOs are synchronized in opposite phase (Stereo mode). NOTE: If P2 or P3 is selected, the speed is adjusted by the SPEED 1 (value knob 2). 5. [. . . ] Are both ends of your bass cable plugged into the correct jacks?Could the rear panel OUTPUT LEVEL knob be turned down?Check the VOLUME, GAIN, BASS, MIDDLE, TREBLE, and PROG LVL settings. For some amp models, you may not hear any sound from the amp if the BASS, MIDDLE, and TREBLE settings are low; this is the same behavior as the circuitry of the original amp. [. . . ]