User manual KORG KAPTIVATOR 1

[. . . ] OWNER'S MANUAL Precautions Location Using the unit in the following locations can result in a malfunction. · In direct sunlight · Locations of extreme temperature or humidity · Excessively dusty or dirty locations · Locations of excessive vibration · Close to magnetic fields Power supply Please connect the designated AC adapter to an AC outlet of the correct voltage. Do not connect it to an AC outlet of voltage other than that for which your unit is intended. Interference with other electrical devices Radios and televisions placed nearby may experience reception interference. Operate this unit at a suitable distance from radios and televisions. Handling To avoid breakage, do not apply excessive force to the switches or controls. Care If the exterior becomes dirty, wipe it with a clean, dry cloth. [. . . ] The display will indicate "A1. **" and the EDIT key will blink. 3 Press the EDIT key several times to choose parameter B5. Here you can choose the controller that will modify the effect. To choose the ribbon controller, choose a setting in the range of "G1"­"G4. " With the "G1" setting, the effect will intensify as you move the controller from bottom to top. Conversely with the "G2" setting, the effect will intensify as you move from top to bottom. With the "G3" setting, the effect is at maximum at either end, and minimum in the center. The "G4" setting produces the opposite result, with the maximum effect in the center position. 4 When you're finished editing, press the YES/WRITE key. Use the VALUE knob to select the destination style location (style number) where you want to save the edited style. Then press the YES/WRITE key to finish saving. If you decide not to save the changes you made, press the NO/ESC key. Changing the wipe type 1 Select the style that you want to edit. For this example, choose style number "11". 2 Hold down the EDIT key and press the STYLE key. The display will indicate "A1. **" and the EDIT key will blink. 3 Press the EDIT key several times to choose parameter A2. This parameter specifies the type of transition. Choosing "00" will specify a fade. In this example, let's select "03" to produce a wipe that changes the position of the images. 4 Press the EDIT key to select parameter A3. This selects the controller that will perform the wipe operation. Choose "F1" if you want to specify the fader. Choose "F2" if you want to invert the direction of the fader operation. [. . . ] E : Exclusive message received. MIDI Implementation 97 (3) 1 MOTION SEQUENCE DATA DUMP REQUEST R +----------------+------------------------------------------------+ | Byte [Hex] | Description | +----------------+------------------------------------------------+ | F0, 42, 3n, 77 | Exclusive Header KTV1 | | 0111 1000 (78) | 1 Motion Sequence Data Dump Request 78h | | 0mmm mmmm (mm) | Dump Motion Number (mm = 00h~63h) | | 1111 0111 (F7) | EOX | +----------------+------------------------------------------------+ When this message is received at the MIDI dump page, the 1 MOTION SEQUENCE DATA DUMP(Function:79h) message will be transmitted. The DATA PROCESS(LOAD) ERROR(Function:24h) message will be transmitted in other cases. (4) 10 MOTION SEQUENCE DATA DUMP REQUEST R +----------------+------------------------------------------------+ | Byte [Hex] | Description | +----------------+------------------------------------------------+ | F0, 42, 3n, 77 | Exclusive Header KTV1 | | 0111 1010 (7A) | 10 Motion Sequence Data Dump Request 7Ah | | 0000 pppp (0p) | Dump Motion Page Number (0p = 00h~09h) | | 1111 0111 (F7) | EOX | +----------------+------------------------------------------------+ When this message is received at the MIDI dump page, the 10 MOTION SEQUENCE DATA DUMP(Function:7Bh) message will be transmitted. The DATA PROCESS(LOAD) ERROR(Function:24h) message will be transmitted in other cases. [. . . ]