User manual KORG KP1 1

[. . . ] · PROGRAM knob: Set the MIDI transmission channel (1­16) · PROGRAM MAP keys, FX ON/OFF, HOLD switches: Turn transmission on/off for each type of MIDI message (refer to "Transmission on/off" in the above table). · MIC input jack: 1/4" phone jack · PHONO input jack: RCA phone jack · LINE IN input jack: RCA phone jack · Output You can assign programs to keys 1­6 for convenient selection. "Program map assignments" This shows the currently selected program number, and the location of the point that you touched on the touch panel. "About the PROGRAM/LOCATION display" PROGRAM knob · LINE OUT jack: RCA phone jack · PHONES OUT: stereo mini jack · Power supply: DC 12 V · Dimensions (W x D x H): 7. 99" x 6. 97" x 2. 30" (203 mm x 177 mm x 58. 5 mm) · Weight: 1. 46 lbs. (660 g) · Included item: AC adaptor, Protective label, Preset guide label This knob adjusts the sensitivity of the input sound. [. . . ] · Be careful not to let metal objects get into the equipment. If something does slip into the equipment, unplug the AC adaptor from the wall outlet. Then contact your nearest Korg dealer or the store where the equipment was purchased. THE FCC REGULATION WARNING (for U. S. A) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: · Reorient or relocate the receiving antenna. · Increase the separation between the equipment and receiver. · Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. · Consult the dealer or an experienced radio/TV technician for help. Unauthorized changes or modification to this system can void the user's authority to operate this equipment. CE mark for European Harmonized Standards CE mark which is attached to our company's products of AC mains operated apparatus until December 31, 1996 means it conforms to EMC Directive (89/336/EEC) and CE mark Directive (93/68/EEC). And, CE mark which is attached after January 1, 1997 means it conforms to EMC Directive (89/336/EEC), CE mark Directive (93/68/EEC) and Low Voltage Directive (73/23/EEC). Also, CE mark which is attached to our company's products of Battery operated apparatus means it conforms to EMC Directive (89/336/EEC) and CE mark Directive (93/68/EEC). You can control the sound by using your finger to rub or tap (strike lightly) this panel. Affix the included protective label. PHONES jack, PHONES VOLUME knob MIDI OUT connector Cable hook PHONO input jacks 8 DIST+FILTER 10 DISTORTION 11 PHASER 12 PHASER 13 LFO WAH 14 STEP PHASER 15 DIST+PHASER 16 MANUAL FLANGER 17 MANUAL FLANGER 18 PITCH SHIFT 19 TREMOLO 20 STEP PHASER 21 TAPE ECHO 22 DELAY 23 DELAY 24 STEREO TAPE ECHO 25 MEDIUM DELAY 26 LONG DELAY 27 X DELAY FX BALANCE, DIST GAIN Rub fast with beat A record turntable can be connected to these jacks. GND (ground) terminal 9 ISOLATOR TYPE FILTER FREQ FREQ (MANUAL) DI/FX BALANCE, RESONANCE Rub slowly Loop the cable around this hook to prevent accidental disconnection. DC IN jack POWER switch LINE OUT jacks Connect this to the ground terminal of your record turntable. TRIM Connect the included AC adaptor (DC12 V 700 mA ) to this jack. CONNECTION switch Adjust this as appropriate for the sensitivity of your mic, so that distortion does not occur. Connect these jacks to your mixer or audio system. MIC input jack A mic can be connected to this jack. LINE IN (input) jacks Normally you will set this in the DIRECT position. If you are using the KAOSS PAD in the send/return loop of your mixer, set this to FX LOOP, so that the original (unprocessed) portion of the sound will not be output. When you use programs 1­10 for FX LOOP, please turn off the direct signal of the mixer. A CD player etc. Use the LINE IN L jack for a monaural connection. Program map assignments 1 Press one of the PROGRAM MAP keys. [. . . ] 5 To re-record, press the REC switch again. The previously-recorded phrase will be erased, and a new phrase will be recorded. If you turn off the power switch or change programs, the recorded phrase will be erased. 28 TALK FILTER+DELAY FILTER FREQ 29 DIST+FILTER+DELAY FREQ 30 DELAY+FILTER FOR DUB TIME 31 REVERB (HALL) 33 REVERB (PLATE) 35 DELAY+REVERB 36 DELAY+REVERB LOW CUT LOW CUT DELAY LEVEL DELAY TIME 32 GATE REVERB (HALL) LOW CUT 34 GATE REVERB (ROOM) LOW CUT 37 TALK FILTER+REVERB FILTER FREQ 38 DIST+FILTER+REVERB FILTER FREQ 39 REVERB+PAN 40 REVERB 41 STEP MODULATION 42 RING MOD+FILTER 43 RING+TALK MOD 44 SPECIAL ECHO 45 RING+DELAY 46 DELAY+TREMOLO 47 3D PAN 48 VIBRATE 49 STEP FLANGER 50 STEP PHASER 51 SAMPLE/PLAY1 52 SAMPLE/PLAY2 53 SAMPLE/PLAY3 PAN REVERB TIME MOD DEPTH RING FREQ MOD SPEED TIME TIME PAN (L/R) SPEED+DEPTH LFO SPEED LOOP TIME TIME STRETCH REV LEVEL+RESONANCE Tap with snare drum Handling the touch panel Never press down too hard on the touch panel, or place a heavy object on it. Rough handling can cause it to crack or break. [. . . ]