User manual KORG M3 EXB RADIAS

[. . . ] E 4 About this manual About the EXB-RADIAS for M3 operating manual This EXB-RADIAS for M3 operating manual explains the RADIAS program functions and parameters that are available when the EXB-RADIAS synthesizer board is installed in the M3 music workstation/sampler. For details about basic operation of the M3 and on the functions and parameters not related to the EXB-RADIAS, refer to the M3 operation guide and parameter guide. Conventions in the operating manual Abbreviations in the operating manual OG, PG When indicating reference pages, the various operating manuals of the M3 may be abbreviated in the following ways. M3 OG: M3 Operating Guide M3 PG: M3 Parameter Guide Parameters in the LCD display screen " " Parameters displayed in the display are enclosed in double quotation marks " ". Symbols , , Note, Tips These symbols respectively indicate a caution, a MIDIrelated explanation, a supplementary note, or a tip. Example screen displays The values of the parameters shown in the example screens of this manual are only for explanatory purposes, and may not necessary match the values that appear in the display of your instrument. MIDI-related explanations CC# is an abbreviation for Control Change Number. In explanations of MIDI messages, numbers in square brackets [ ] always indicate hexadecimal numbers. * Company names, product names, and names of formats etc. [. . . ] OSC1 Control2 (000. . . 127/­63. . . +63/01. . . 32/ LPF63. . . CNT. . . HPF63/01. . . 64l/L63. . . CNT. . . R63, Absolute): Controls a parameter appropriate for the modulation type of oscillator 1. (000. . . 127): Controls the amount of change in the oscillator 1 waveform. This can be controlled if the OSC1 Mod is Waveform or Cross. Unison Phase (000. . . 127): Controls the relative phase of the oscillators at note-on. This can be controlled if OSC1 Mod is Unison. VPM Harmonics (01. . . 32): Controls the VPM modulator frequency. This can be controlled if OSC1 Mod is VPM. Formant Offset (­63. . . +63): Shifts the frequency spectrum of all formants. This can be controlled if OSC1 Waveform is Formant. LPF/HPF Mix (LPF. . . CNT. . . HPF): Controls the mix balance between the low pass filter and high pass filter inside the noise generator. This can be controlled if Waveform is Noise. Wave Select (00. . . 63): Selects the DWGS waveform. This can be selected if the OSC1 Waveform is DWGS. Balance (L001. . . C064. . . R127): Controls the left/right channel balance of the input signal. This can be controlled if the OSC1 Waveform is AudioIn. OSC2 Waveform (Saw. . . Sine, Absolute): Selects the oscillator 2 waveform. OSC2 Mod (Off/Ring. . . RingSync, Absolute): Selects the modulation type for the oscillator. OSC2 Semitone (­24. . . +24, Absolute): Controls the amount of detune (semitone units) relative to oscillator 1. OSC2 Tune (­63. . . +63, Absolute): Controls the amount of detune relative to oscillator 1. OSC1 Level (000. . . 127, Absolute): Controls the output level of oscillator 1. OSC2 Level (000. . . 127, Absolute): Controls the output level of oscillator 2. Noise Level (000. . . 127, Absolute): Controls the output level of the noise generator. FilterA Type/Balance (LPF24. . . LPF12. . . HPF. . . BPF. . . THRU, Absolute): Selects the filter type for filter A. [. . . ] Press the OK button to execute, or press the Cancel button to cancel. If you specify Single as the range to be loaded, select a program from bank I­F as the load-source, and a program number in I­F or a user bank set to the RADIAS bank type as the load-destination ("To"). 65 Parameter guide Set Program User­Bank Type This specifies the bank type for Program mode program banks USER­A through G. If you've set the bank type to RADIAS, the RADIAS programs you create can be saved in the corresponding user bank. As an example, here's how to set the USER­F bank type to RADIAS. Before you execute, uncheck Program in Memory Protect (M3 parameter guide p. 359). [. . . ]