User manual KORG MINI KAOSS PAD 2

[. . . ] Do not connect it to an AC outlet of voltage other than that for which your unit is intended. Interference with other electrical devices This product contains a microcomputer. Radios and televisions placed nearby may experience reception interference. Operate this unit at a suitable distance from radios and televisions. Handling To avoid breakage, do not apply excessive force to the switches or controls. Care If the exterior becomes dirty, wipe it with a clean, dry cloth. Do not use liquid cleaners such as benzene or thinner, or cleaning compounds or flammable polishes. Keep this manual After reading this manual, please keep it for later reference. Keeping foreign matter out of your equipment • Never set any container with liquid in it near this equipment. [. . . ] If the MIDI Clock parameter is set to "Ext" (external), the delay time can also be synchronized to the clock of an external device. (Refer to p. 39 "Synchronizing the EA-1 and an external MIDI device. ") • Depth (delay depth) 0. . . 100 Adjust the depth of the delay and the amount of feedback (the number of delay repeats). Rotating the knob toward the right will increase the level of the delayed sound and the amount of feedback. Raising the Depth excessively may cause the sound to distort. 25 4. Pattern mode ○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○ Resonance 0. . . 100 • Time (delay time) This parameter adds character to the sound by boosting the region around the cutoff frequency. If you raise the resonance and turn the Cutoff knob (or adjust EG Int and Decay), you will hear the typical "meow-ing" sound typical of analog synthesizers. If the resonance is raised, the sound may be distorted depending on the cutoff frequency or on the pitch that you play. 4. Pattern mode 1/4. . . 8 Set the delay time. Rotating the knob toward the right will lengthen the delay time. If you have selected Tempo Delay as the effect type, this parameter will let you set the tempo in terms of sixteen different multiples of the step: 1/4, 1/3, 1/2, 2/3, 3/4, 1, 1. 33, 1. 5, 2, 2. 5, 3, 4, 5, 6, 7, or 8. Depending on the tempo setting, it may be impossible to set the delay time. In such cases, set the delay time to half the desired value. EG Int (EG intensity) –100. . . 0. . . 100 Specify the depth and direction of the effect that the EG (envelope generator) will have on the cutoff frequency. The EG will start when trigger-on occurs (the instant you play the keyboard). Rotate the dial to select the pattern for which you wish to make Swing settings. Hold down the Shift key, and press step key 8 (Swing). Once again press step key 8 to execute the Swing setting (key 8 will go dark). If you decide to cancel without making the setting, press the Stop/Cancel key. If the Length and Beat/Scale settings are set to triplets ( 3 x 12), the Swing setting has no effect. It is not possible to view or adjust the Swing parameter during playback or recording, or during Pattern Set Play. 16 32 48 64 12 24 36 48 2, 4 Correspondence between step keys and note values 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 3 3 3 3 3 3, 5 1 2 3 4 5 6 7 8 9 10 11 12 About the Target Step Target Step 1. 01. . . 4. 16 Changing the trigger settings 1. Turn off the Keyboard function key (the key will be dark). Use the cursor keys to make the parameter select LEDs indicate either Pattern, Tempo, or Step Rec. Use the Part Select key to select the part that you wish to edit. For a pattern with a pattern length of 2 or more, you can use the Select keys to move the red select LEDs to left or right to change the length location that you will edit. The step keys will light to indicate the trigger locations of the pattern for that part. [. . . ] When event-recording on a song, event data memory has filled up. If you attempt to record additional events, the "memory full" message will appear immediately. Either use Clear Event to delete unwanted events from a song, or record blank data to clear the memory. Restoring the factory set data The pattern and song data with which the EA-1 is shipped from the factory is referred to as the "preloaded data, " and you can restore this preloaded data back into the memory of the EA-1. When you do this, the patterns you created and the songs which use these patterns will be erased, and replaced by the preloaded data. [. . . ]