User manual KORG MS-20 SERVICE MANUAL

[. . . ] (Manual: p. ): Refers to a page in the "D32XD/MS-20 Owner's Manual" Warning dialog box added to Format and Partition Change in PC drive size --------------------------- 4 ------------ 4 4 4 5 5 Changes and additions to Edit Track Updating the system For the procedure of how to update the system, refer to the owner 's manual section on "Updating the system" (Manual: p. 95). Optimizing a track (OptimizeTrk) ----------------------------Eliminating noise (NoiseReduction) --------------------------Erasing punch noise (ErasePunchNoise) -------------------Erase a silent region (EraseSilence) -------------------------- New MIXER Navigation Tools Equalizer knobs Added message 1 Added message 2 Added Mixer SetUp -------------------- 6 -------------------------------------- 6 ----------------------------------- 6 ----------------------------------- 6 --------------------------------- 6 CAUTION FOR LASER This product utilizes a laser. Use of control, adjustment or performance of procedures other than those specified herein may result in hazardous radiation exposure. Do not open covers and do not repair yourself. Laser diode properties Material Semiconductor laser GaAlAs Laser output Less than HHS and IEC 825-1 Class 1 Limit Wave length 784 nm Accessing the Mixer Setup screen ---------------------------- 6 Storing a mixer setup ------------------------------------------- 6 Recalling a mixer setup ----------------------------------------- 7 Top panel keys SCRUB --------------------------------------- 7 -------------------------------------------------- 7 Location of the required label. The following enhancements apply only to the MS-20 ------------------ 8 Changes in PAIR page mode Event Automation --------------------- 8 ----------------------------------- 9 2 Added functionality Control knobs The control knobs can now be used to edit various parameters in the following pages. [. . . ] (4) Press the Store button to open the Store Program dialog box. If you decide that you want to store the settings in a program number other than the one shown in the cell, you can press to highlight it and use the value dial (or the +/ ­ keys) to change the program number. CD key (Manual: p. 10, 122) Pressing the CD key displays the page jump menu screen. Pressing the CD key again displays the most recently selected page within the page jump menu. Pressing the CD key yet again returns to the page jump menu screen. In this way you can alternate between the page screen and the page jump menu screen by pressing the CD key. (5) (4) (6) UNDO key (Manual: p. 10) Pressing the UNDO key displays the "Undo/Redo" tab page. Pressing the UNDO key again returns to the page in which you were prior to pressing the key. (5) If you want to assign or edit the program name, press the Rename button to open the Rename dialog box. Press the Yes button to save the settings. If you decide to cancel, press the No button. SCRUB key (Manual: p. 11, 40, 148) Pressing the SCRUB key displays the "Scrub" page. Pressing the SCRUB key again returns to the page in which you were prior to pressing the key. Recalling a mixer setup Here's how to recall a previously-stored mixer setup program. You can't recall a setup while a song is playing. SCRUB (Manual: p. 40, 148) While the "Scrub" page is displayed, you can use the LOC1­ LOC6 keys, MARK JUMP ®, or the counter to change the location just as when you're in other pages (Manual: p. 38). You can also change the location by using the STOP key and MARK JUMP ® keys in combination (Manual: p. 151). If you want to return to scrubbing after you've used the counter to change the location, press a button outside the waveform window or counter, or press the cursor key. (1) Access the MIXER, "MIXER SET UP, " "MixerSetUp" tab page. To assign the channel to a group, press the corresponding button (it will be highlighted). Group on buttons [A, B, C, D] To activate a particular fader group, press the corresponding button (highlighted). If these buttons are pressed, the fader levels will change to preserve the balance of the group when you operate any fader in that group. When you turn on a 1. "Group button" to add a channel to an existing group, the level of the channel at that moment will be set as that fader's balance in the group. 8 Event Automation Both the D32XD and MS-20 support Scene Automation. Previously, only the D32XD supported dynamic Event Automation. The MS-20's FADER/PAN/AUTOMATION page mode has been changed to include the same dynamic Event Automation found on the D32XD (Manual: p. 103). The MS-20 is not equipped with motorized faders, so in order to see the dynamic automation taking place, use the Mixer View (Manual: p. 107) or Meter Trk View (Manual: p. 97) This change adds Automation and Event List pages (Manual: p. 104). Please also refer to the Operation section (Manual: p. 54). 4. Automation This button turns the playback and recording of automation events on and off. OFF: Automation playback/recording will not occur. On (Play): Turn on the automation playback. [. . . ] To cut all events in the event list, press (highlight) the Select All button and then execute Cut. Copy Press this button to open the Copy Event dialog box. The selected event will be copied temporarily to the edit buffer (clipboard). To execute the copy, press the Yes button. [. . . ]