User manual KORG TRITON EXTREME

[. . . ] E 2 Thank you for purchasing the Korg TRITON Extreme music workstation/sampler. To ensure trouble-free enjoyment, please read this manual carefully and use the instrument as directed. About this manual The owner's manuals and how to use them The TRITON Extreme come with the following owner's manuals. · Quick Start · Operation Guide · Parameter Guide · Voice Name List Conventions in this manual References to the TRITON Extreme The TRITON Extreme is available in 88-key, 76-key and 61-key models, but all three models are referred to without distinction in this manual as "the TRITON Extreme. " Illustrations of the front and rear panels in this manual show the 61-key model, but the illustrations apply equally to the 88-key and 76-key models. Abbreviations for the manuals QS, OG, PG, VNL, EM The names of the manuals are abbreviated as follows. QS: Quick Start OG: Operation Guide PG: Parameter Guide VNL: Voice Name List EM: EXB-MOSS Owner's Manual (included with the EXB-MOSS option) Quick Start Read this manual first. [. . . ] ("The recording level and "Auto +12 dB On"") In Sampling mode, you can set this parameter in the P0: Recording, Preference page. 66 In Program, Combination, and Sequencer modes, you can set this parameter using the Sampling page menu command "Select Bank & Smpl. MEDIA: The sample will be written to the media. If you select MEDIA, you can also select the writingdestination drive. In all modes, this is specified by the page menu command "Select Directory. " When you sample an external audio source, you should normally set "Recording Level" to +0. 0 (dB). The sample data will be recorded at the optimum level. If you sample with "Auto +12 dB On" turned off at this time, "+12 dB" (Sampling mode Loop Edit page) will be off, and the sample will play back at the same level at which it was sampled. When the power is turned on, "Recording Level" and "Auto +12 dB On" will default to the following settings. Program, Combination, Sequencer modes "Recording Level": ­12. 0 (dB), "Auto +12 dB On": on Sampling mode "Recording Level": +0. 0 (dB), "Auto +12 dB On": off These settings assume that you will mainly be resampling in Program, Combination, and Sequencer modes (listed above), and performing conventional sampling in Sampling mode (listed below). Media Select Optimizing the sample memory (RAM) In the "Media Select" field, select the drive. Use the Open and Up buttons to move between levels of the directory hierarchy to select the desired directory. Press the Done button to finalize the settings. If you sampled to the media as a WAVE file, the "Auto +12 dB On" setting will be ignored. The playback level of the WAVE file is set by "WAVE File Play Level" (PG p. 158). 2 In "Sample Time, " specify the length of time that you want to sample. This can be set in units of minutes and seconds. If you are sampling to RAM (sample memory), you can sample a maximum of approximately 2 minutes 54 seconds in mono, or approximately 1 minute 27 seconds in stereo. If you are sampling to MEDIA, you can sample a maximum of 80 minutes in either mono or stereo (mono: approximately 440 Mbytes, stereo: approximately 879 Mbytes). 3 Set "Sample Mode" to specify whether a mono or a stereo file will be created. L-Mono: The sound of the internal L channel will be sampled in mono. R-Mono: The sound of the internal R channel will be sampled in mono. Stereo: The sound of the internal L and R channels will be sampled in stereo. If RAM has been specified as the destination to which data will be written during sampling, you can specify that sample memory (RAM) be automatically optimized after the data is written. When optimization is performed, unused areas that are occupying memory space will be reorganized to increase the available free space. [. . . ] You may also check the Korg website (http:// www. korg. com/downloads). External USB storage media · HD: hard disk · RM: removable disk (Magneto-Optical) MS-DOS format FAT16 and FAT32 are supported for HD and RM. Capacity recognized: FAT32: up to 2 Tbytes = 2, 000 Gbytes FAT16: up to 4 Gbytes · CDR (CD-R/RW) UDF format is supported. UDF format CD-R/RW can be written and read. (Packet writing support PG p. 330) CD-DA (audio data) can be recorded/played, and ISO9660 (level 1) format can be loaded. [. . . ]