User manual KURZWEIL DIGITAL GRANDE DC 150

[. . . ] Product features and specications are subject to change without notice. Part Number: 910329 Rev. A CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE THE COVER NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL The lightning flash with the arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product. IMPORTANT SAFETY & INSTALLATION INSTRUCTIONS INSTRUCTIONS PERTAINING TO THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS WARNING: When using electric products, basic precautions should always be followed, including the following: 1. Read all of the Safety and Installation Instructions and Explanation of Graphic Symbols before using the product. [. . . ] No MIDI signals are sent if the value is Off. Destination Int, Mid, Bot This species where your performance data should be sent. Int means the internal sound module, Mid means MIDI, and Bot means both. Internal Effect 0-9, Noc This is the effect number for the currently-selected sound. A value of 0 means no effect, and Noc (no change) means the effect doesnt change when this sound is selected. As you select different sounds, the value of this parameter will change. Transpose -60 to 60 Subtracts or adds the specied number of semitones to the notes you play. Caution: changing this parameter while keys are down may cause stuck notes. Velocity Curve 1-8 Allows you to alter the relationship between keyboard playing effort (keystroke velocity) and the resulting sound volume (for velocity sensitive voices). See page 4-11, and Velocity Curve on page 4-6 for more. Reverb Wet/Dry, Chorus Wet/Dry 0-100, Noc This is the effect intensity for the currently-selected sound. Noc means that the effect intensity doesnt change when this sound is selected. A Ribbon 0-129, Off Species where signals from the left ribbon are sent. See the Info Strip for corresponding MIDI controller names. Default is Pitch Wheel, which the internal sound module does not respond to. Hold or Center Hld, Ctr Species whether the A ribbon signal remains at its last value or returns to center when your nger is lifted. Default is Center (Ctr). B Ribbon Up, B Ribbon Down 0-129 and Off Species where signals from the two halves of the right ribbon are sent. Defaults are Modulation Wheel (01) and Pan (10) respectively. The following assumes that you are in Edit mode. Selecting a Parameter The names of all 30 possible parameters are listed in the Parameters area. The listing is in 3 columns (Left, Right, and Global) and 6 rows. In each column, there are 1 or 2 parameters per row. The 2 column-designator LEDs indicate a column, either Left or Right. If both are off, then the Global column is current. The 6 row-designator LEDs indicate a row. If the LED is on continuously, then the upper parameter of the pair is current. If it is blinking, the lower parameter is current. To select a different column, press the Col Select button repeatedly until the column LEDs indicate the desired column. Note that the current row LED may change from blinking to continuous when you change to a column with only one parameter for the current row. To select a different row, press the Row Select button until the desired row and parameter are selected. [. . . ] After each run, the pass count will be displayed briey. If more than 255 times, the count will remain at 255. Jumper Settings Display This diagnostic displays the settings of the 4 hardware jumpers. These jumpers identify the keyboard length and type plus other conguration information to the software. After noting the display, press Row Select to return to the main diagnostic menu. Exiting Diagnostics The simplest way to exit diagnostics and resume normal operation is to turn the power off then on again. [. . . ]