User manual KURZWEIL RE-110 MUSICIAN S GUIDE

[. . . ] 178-353 Gajwa-dong, Seo-gu, Incheon, KOREA Tel:82-32-580-1500 Fax:82-32-584-4863 AND Music Corporation 10107 South Tacoma Way, Suite A-3 Lakewood, WA 98499 Tel:(253)589-3580 Fax:(253)589-3585 2006. 10 Rev. A RE-110 Digital Piano Owner's Manual Table of Contents Important Safety & Installation Instructions Important Safety Instructions The Panel of the RE-110 Introduction The Features of the RE-110 Setting up the Instrument VOICE Button Main Voice Reverb & Chorus Demo Song SPLIT Button Split Point Lower Voice Upper Voice Lower Octave Shift Upper Octave Shift 4-Hand Setup FUNCTION Button Touch Tune Transpose MIDI Receive and Transmit Channel Local Control Reset Pedals 4 5 6 7 8 12 13 14 15 15 15 16 16 16 17 17 18 19 20 20 Sustain Pedal Sostenuto Pedal Soft Pedal MIDI MIDI Connection MIDI Channels Miscellaneous Headphone Audio In Jack Audio Out Jack MIDI Implementation Chart Appendix Specifications Quick Operation Guide 21 21 21 22 23 24 24 24 25 26 27 www. ycpiano. co. kr www. kurzweilmusicsystems. com The lightning flash with the arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product. IMPORTANT SAFETY & INSTALLATION INSTRUCTIONS INSTRUCTIONS PERTAINING TO THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS WARNING : When using electric products, basic precautions should always be followed, including the following: 1. Read all of the Safety and Installation Instructions and Explanation of Graphic Symbols before using the product. [. . . ] Use the screw to fasten the bottom of the rear panel. Setting up the Instrument 9 Attach the Keyboard 1. Place the keyboard on the stand so that the wood pegs on the bottom of the keyboard fit into the holes in the side panel brackets. Fasten the keyboard to the side panel using screw numer 3. Insert the pedal cable connector into the pedal jack located on the bottom of the keyboard. Be sure that the connector is inserted in the correct orientation. Make sure that the cable clamp fastens to the pedal cable. 4. Rotate the pedal adjuster until it comes in firm contact with the floor surface. If the adjuster is not in firm contact with the floor, the pedal will wobble and cause malfunctions. Install the headphone hanger as shown in the figure. 10 Setting up the Instrument Turning on the Instrument (Power) The RE-110 operates on AC adapter power. A power cord is included with the AC adapter to connect it to an AC outlet. Before connecting the power cord, be sure that the power switch, located left side of the keyboard, is off. First plug the adapter's small, round plug in the matching jack in the back of the piano. Then plug the power cord into an AC outlet. Once the power cord is connected, you can turn the power switch on. Setting the Volume To be sure that you can hear the instrument, turn the Volume knob (on the upper side of the left panel) to the middle of its range. This should be a reasonably comfortable level of volume which you can adjust if you wish the sound to be louder or softer. Setting up the Instrument 11 VOICE Button Please refer to the Voice Button section of the Quick Operation Guide on page 27 while reading the following sections. MAIN VOICE To select one of the 10 primary voices, hold down the Voice button then press and release a keyboard key between C1 and A1. Piano, hold down Voice, press and release the E1 key, then release Voice. A ratio of 50% will be about half and half while 90% will be nearly all effect sound. Adjust the reverb wet/dry amount for the selected reverb type by pressing one of the C4 ~ A#4 keys while holding down the Voice button. The wet/dry mix range is from 0 to 100%. The default reverb type and wet/dry amount are Room and 10% respectively. Key C4 C#4 D4 D#4 E4 F4 F#4 G4 G#4 A4 A#4 0 Reverb Wet/Dry 10 (Default) 20 30 40 50 60 70 80 90 100 Key C5 C#5 D5 D#5 E5 F5 F#5 G5 G#5 A5 A#5 Chorus Wet/Dry 0 (Default) 10 20 30 40 50 60 70 80 90 100 Voice Button 13 Chorus Wet/Dry Mix While holding down the Voice button, press one of the C5 ~ A#5 keys to select the chorus wet/dry amount. The default wet/dry amount for chorus is 0%. If you select Effect Off for the reverb type, then the chorus effect will also be turned off and you will only hear the direct sound. DEMO SONG While holding down the Voice button, press one of the C6 ~ F6 keys to select and play a demo song. If you want all demo songs to be played in a loop, press the F6 key. [. . . ] MIDI Out sends MIDI messages to other equipment. MIDI cables provide the connection between the MIDI ports of one piece of equipment and those of another. To keep things simple, there are only two valid MIDI connections: Out to In, In to Out. The simplest use of MIDI is to play two instruments at a time from the keyboard of one of them. [. . . ]