User manual KURZWEIL SMP18SUP

[. . . ] BETA TEST VERSION 1. 8 SUPPLEMENT TO: VERSION 2. 0 ADDENDUM TO: KURZWEIL 150 FOURIER SYNTHESIZER SOUND MODELING PROGRAM VERSION 1. 0 USER'S GUIDE Rev. A MARCH 23, 1989 This supplement describes the new features of Beta Test Version 1. 8 of the Apple II Sound Modeling Program for the Kurzweil 150 Fourier Synthesizer. Among these is a new version that will run properly on an Apple II-GS with a Passport (or equivalent) MIDI interface card. In addition, some bugs in Version 1. 7 have been fixed. [. . . ] The printer must be set up for DTR handshaking (using the "Handshake-In" pin in the 8-pin connector) and the baud rate set by the control panel must match the printer. The control panel handshake options don't matter to this program. . S. M. P. A 23-MAR-89 SMP-SCREENPRINT-IMGWRTR-2CPP This file is for an Apple Imagewriter connected to the Printer Port of an Apple IIc or an Apple "Super Serial" card plugged into slot 1 of an Apple IIe or II+. The printer must be set up for DTR handshaking and 9600 baud. SMP-SCREENPRINT-IMGWRTR-SSS2 This file is for an Apple Imagewriter connected to an Apple Super Serial card plugged into slot 2 of an Apple IIe or II+. It also may work through the modem port of an Apple IIc. The printer must be set up for DTR handshaking and 9600 baud. Since the MIDI interface card cannot also be in slot 2, you will have to put it into another slot and run SLOTPATCH as described in Section 2. 4 of the 2. 0 Addendum. SMP-SCREENPRINT-IMGWRTR-SSS4 This file is the same as above except for a Super Serial card in slot 4. SMP-SCREENPRINT-IMGWRTR-2ESI This file is for an MPC Peripherals AP-SIO card or equivalent in slot 1 of an Apple IIe or II+. This interface uses a 6850 chip rather than the 6551 chip used in the Super Serial card. The program should work with other 6850-based serial cards. The printer should be set for DTR handshaking and the baud rate set by the card's DIP switches should match the printer. SMP-SCREENPRINT-IMGWRTR-2ES4 This file is same as above except for Slot 4. SMP-SCREENPRINT-IMGWRTR-2ES2 This file is same as above except for Slot 2. The MIDI interface card will therefore have to be moved to another slot and SLOTPATCH run. If none of the programs above are suitable, or you are using a parallel printer interface or a printer with a non-Applewritercompatible command set, you will have to obtain or write your own screen print program. imposes the following restrictions on the screen print program: 1. It must reside in memory at addresses $300-$3CF and have its entrypoint at $300. It must print page 1 of the high-resolution screen at $2000-$3FFF. It may freely use page zero memory addresses $56-$65. Other locations are usable if they are saved and restored (use the text screen area or part of itself for temporary storage). It must make balanced use of the stack and return to the caller with an RTS instruction after the printout is complete. The machine registers A, X, and Y may be freely used and the decimal mode should remain off. [. . . ] It is possible for an initially valid shift, skew, stretch or compress value to be skewed to a ridiculous extreme after a few partials with possibly . S. M. P. Thus save your model first, then check the current skew value, initial value, and number of partials that will be processed before executing the function. Be particularly wary if the function warns that "Overlapped breakpoints will be deleted" and you didn't expect that to happen. 3. 3 K150FS PROGRAM RENAME FUNCTION This minor addition to the LOAD/SAVE PROGRAM menu allows you to edit the name of any program in the K150FS quickly and easily (much more easily than using the 150's front panel). To change the name of a program, press 4 (FROM K150FS) and enter the number of the program you wish to change. [. . . ]