User manual KUSSMAUL 091-22F-A

[. . . ] An LED indicator on the front face is illuminated when the engine is in HIGH IDLE. VOLTAGE MONITOR: This module interfaces with the Engine Idler module to activate the high idle system whenever the detected voltage drops. Three LED's indicate High, Low or Normal battery voltage. When the battery voltage is above 15. 6 volts D. C. [. . . ] The LOW battery voltage indicator illuminates when the battery voltage is below 12. 5 volts. At this time a signal is sent to the Engine Idler module automatically placing it in high idle. This occurs only if the transmission is in Park or Neutral and the brake pedal is not depressed. INSTALLATION Typical installations are illustrated in figures 1 through 4. Mount actuator and solenoid valve in an appropriate location and connect the actuator output to the throttle mechanism. (Note: The actuator and solenoid valve must be purchased seperately. Kits that simplify the actuator mounting and connection are available for several engines. Be certain that the ball chain or other coupling does not restrict throttle motion at full closed throttle or wide-open throttle. Connect solenoid valve air lines and electrical wiring as illustrated. OPERATION The High Idler receives its power from the ignition switch and functions only when the ignition switch is either "ON" or in the ACC. High Idle is automatically disabled under any of the following conditions: 1. Note that when the voltage drops below 12. 5 volts, the following occur: a. The Low indicator on the Voltage Monitor illuminates. The indicator on the Engine Idler illuminates. The High Idle System is active and the engine is speeded up. CAUTION FORD INSTALLATIONS FORD, in many installations uses a starter solenoid which has one side of the coil grounded. The neutral safety switch is then placed in the supply side of the solenoid coil. This configuration creates a considerable voltage spike when the vehicle is started. A diode must be placed across the starter solenoid in these installations to prevent damage to the engine idler. See the appropriate wiring diagram for diode installation details. CHAIN, CONNECT TO THROTTLE LINKAGE VACUUM ACTUATOR BRAKE LIGHT 091-84-VA BATTERY + Stroke adjust BRAKE SWITCH DIODE On some vehicles install diode to prevent emergency flasher or turn signals from turning off the engine idler TO VACUUM SOURCE NEUTRAL SAFETY SWITCH CLOSE IN NEUTRAL/PARK OUT 091-84-VV SOLENOID AIR VALVE IN 1 amp fuse To +12 volts thru accessory position of Ignition switch KUSSMAUL OFF ON ENGINE IDLER ENGINE IDLER INSTALLATION Figure 1 CHAIN, CONNECT TO THROTTLE LINKAGE BRAKE LIGHT VACUUM ACTUATOR BATTERY + 091-84-VA Stroke adjust BRAKE SWITCH DIODE On some vehicles install diode to prevent emergency flasher or turn signals from turning off the engine idler +12 volts from ignition switch in "START" position Starter Solenoid SOURCE SEE NOTE: Connect 1N4004 as shown to suppress starter solenoid transient NEUTRAL SAFETY SWITCH CLOSED IN NEUTRAL OR PARK OUT 091-84-VV SOLENOID AIR VALVE IN 1 amp fuse To +12 volts thru accessory position of Ignition switch NOTE: Some engines have one side of starter solenoid at ground and the neutral safety switch in the supply side. These must have a diode installed across the starter solenoid as illustrated. KUSSMAUL OFF ON ENGINE IDLER ENGINE IDLER INSTALLATION FOR ENGINES WITH NEUTRAL SAFETY SWITCH CONNECTED TO STARTER Figure 2 CHAIN, CONNECT TO THROTTLE LINKAGE VACUUM ACTUATOR BRAKE LIGHT 091-84-VA Stroke adjust BRAKE SWITCH DIODE On some vehicles install diode to prevent emergency flasher or turn signals from turning off the engine idler BATTERY + SOURCE NEUTRAL SAFETY SWITCH CLOSE IN NEUTRAL/PARK OUT IN 091-84-VV SOLENOID AIR VALVE 1 amp fuse To +12 volts thru accessory position of Ignition switch KUSSMAUL OFF ON HIGH KUSSMAUL LOW ENGINE IDLER VOLTAGE MONITOR VOLTAGE MONITOR & ENGINE IDLER INSTALLATION AND WIRING DIAGRAM Figure 3 CHAIN, CONNECT TO THROTTLE LINKAGE BRAKE LIGHT VACUUM ACTUATOR BATTERY + 091-84-VA Stroke adjust BRAKE SWITCH DIODE On some vehicles install diode to prevent emergency flasher or turn signals from turning off the engine idler +12 volts from ignition switch in "START" position SOURCE Starter Solenoid SEE NOTE: Connect 1N4004 as shown to suppress starter solenoid transient NEUTRAL SAFETY SWITCH CLOSED IN NEUTRAL OR PARK OUT 091-84-VV NOTE: Some engines have one side of starter solenoid at ground and the neutral safety switch in the supply side. [. . . ] These must have a diode installed across the starter solenoid as illustrated. KUSSMAUL OFF ON ENGINE IDLER ENGINE IDLER INSTALLATION FOR ENGINES WITH NEUTRAL SAFETY SWITCH CONNECTED TO STARTER Figure 2 CHAIN, CONNECT TO THROTTLE LINKAGE VACUUM ACTUATOR BRAKE LIGHT 091-84-VA Stroke adjust BRAKE SWITCH DIODE On some vehicles install diode to prevent emergency flasher or turn signals from turning off the engine idler BATTERY + SOURCE NEUTRAL SAFETY SWITCH CLOSE IN NEUTRAL/PARK OUT IN 091-84-VV SOLENOID AIR VALVE 1 amp fuse To +12 volts thru accessory position of Ignition switch KUSSMAUL OFF ON HIGH KUSSMAUL LOW ENGINE IDLER VOLTAGE MONITOR VOLTAGE MONITOR & ENGINE IDLER INSTALLATION AND WIRING DIAGRAM Figure 3 CHAIN, CONNECT TO THROTTLE LINKAGE BRAKE LIGHT VACUUM ACTUATOR BATTERY + 091-84-VA Stroke adjust BRAKE SWITCH DIODE On some vehicles install diode to prevent emergency flasher or turn signals from turning off the engine idler +12 volts from ignition switch in "START" position SOURCE Starter Solenoid SEE NOTE: Connect 1N4004 as shown to suppress starter solenoid transient NEUTRAL SAFETY SWITCH CLOSED IN NEUTRAL OR PARK OUT 091-84-VV NOTE: Some engines have one side of starter solenoid at ground and the neutral safety switch in the supply side. These must have a diode installed across the starter solenoid as illustrated. This is particularly true of FORD products OFF IN 1 amp fuse SOLENOID AIR VALVE To +12 volts thru accessory position of Ignition switch KUSSMAUL ON HIGH KUSSMAUL LOW ENGINE IDLER VOLTAGE MONITOR INSTALLATION AND WIRING DIAGRAM FOR ENGINES WITH NEUTRAL SAFETY SWITCH CONNECTED TO STARTER Figure 4 VOLTAGE MONITOR & ENGINE IDLER For vehicles that do not have a Neutral Safety Switch or have a digital switch that does not connect to ground. Switch used to sense when vehicle is in park. This is a momentary switch that connects a ground to pin 4 on the Engine Idler Vehicle shown in park Linkage to transmission To pin 4 Engine Idler Ground Transmission Bracket to support switch Instructions Find a suitable momentary switch preferably watertight. [. . . ]