User manual KYOCERA FS-3830N

[. . . ] FS-3820N FS-3830N Page Printers Operation Guide Caution on Installation No liability is assumed for any damage caused by improper installation. Notice on Software Software used with this printer must support the printer's emulation mode. The printer is factory-set to emulate the PCL. The emulation mode can be changed by following the procedures described in Chapter 1. Notice on This Guide The information in this guide is subject to change without notification. Additional pages may be inserted in future editions. [. . . ] Parallel If you want to abandon the interface selection procedure, press the CANCEL key. The interface remains unchanged. 4 5 Press the or key repeatedly until Serial appears. Interface ?Serial Press the ENTER key again. 1-76 Interface 6 Press the > key. Each time the or key is pressed, the setting item and current setting change as shown below. >Baud Rate 9600 >Data Bits 8 >Stop Bits 1 >Parity None >Protocol DTR(pos. )&XON Definable baud rates: 1200, 2400, 4800, 9600 (default), 19200, 38400, 57600, 115200 Definable data bits: 7, 8 (default) Definable stop bits: 1 (default), 2 Definable parity: None (default), Odd, Even, Ignore Definable protocol: DTR(pos. )&XON (default), DTR(positive), DTR (negative), XON/XOFF, ETX/ACK 7 Display the setting item to be changed and press the ENTER key. The following example explains how to change the baud rate. The settings for other items can be changed in a similar manner. >Baud Rate ?9600 8 Press the or key to display the desired setting. The baud rate can be selected from 1200, 2400, 4800, 9600 (default), 19200, 38400, 57600, and 115200. Note Some computers may not be compatible with a baud rate of 115200 bps. If you set the baud rate to 115200 and communication problems occur, lower the baud rate. 9 Display the desired baud rate and press the ENTER key. The message display returns to Ready. 1-77 Interface Network Interface Parameters This printer supports TCP/IP NetWare and EtherTalk protocols. In , addition, you can install the option network interface card in the option interface slot. Using the operator panel, you can: · · · Activate or deactivate TCP/IP NetWare, and EtherTalk , Activate or deactivate DHCP Enter IP address, subnet mask address, and default gateway address To confirm or change network card parameters, proceed as follows: 1 2 Press the MENU key. Press the or key repeatedly until Interface > appears. One of the interface names shown below appears, indicating the current interface. Parallel (default) USB Network Serial (when a serial interface board kit is installed) Option (when a network interface card is installed) 3 Press the ENTER key. A blinking question mark (?) appears. Interface ?Parallel If the option network interface card is installed in the printer, Option will be displayed. The setting procedure is basically the same even in this case. 4 5 Press the or key repeatedly until Network appears. Interface ?Network Press the ENTER key again. 1-78 Interface 6 Press the > key. Each time the changes as shown below. or key is pressed, the display Range >NetWare On > Set this item to On when you connect to a network using NetWare. In submenu (>), frame mode can be selected from Auto, Ethernet, 802. 2, 802. 3, and 802. 3 SNAP . Set this item to On when you connect to a network using TCP/IP Submenu (>) has . [. . . ] KM-NET VIEWER is contained on the CD-ROM supplied with the printer. Emulation This refers to emulation of manufacturers' printers. The printer emulates operation of the following printers: PCL, Line printer, IBM Proprinter, DIABLO 630, EPSON LQ-850, KPDL. MB (mega byte) This unit is used to express data quantities and memory capacities. 1 MB is equivalent to 1024 kB, or 1, 048, 576 bytes. Expansion memory This option is used to increase printer memory. The printer has an expansion socket, into which you can install a 32 MB, 64 MB, 128 MB, or 256 MB DIMM (Dual Inline Memory Module). [. . . ]