User manual KYOCERA FS-9100DN

[. . . ] Operation Guide Please read this Operation Guide before using the printer. Keep it close to the printer for easy reference. Please read the Operation Guide before using the printer. Keep it close to the printer for easy reference. The sections of this guide and parts of the printer marked with symbols are safety warnings meant to protect the user, other individuals and surrounding objects, and ensure correct and safe usage of the printer. [. . . ] None (default) Short edge bind Long edge bind Adjusting the Stitch Positions When installing the option document finisher DF-75, adjust the stitch positions using the following procedures. In the default settings, the stitch position is set in the center of the paper. Depending on the paper, a certain amount of deviation will occur. In this case, also use this menu to adjust the stitch position. The adjustment can be done by moving the stitch position adjustment gear in the document finisher. For example, select the range from -57 to +57 (1 = approximately 0. 14 mm) to move the stitch position approximately 8 mm as shown in the following figure. The default setting is 000 (center of the paper. ) Default stitch position (center of the paper) 7 8 When the desired duplex mode is displayed, press the ENTER key. The message display returns to Ready. Selecting the Output Device You can select whether printouts will be received by the printer's face-down output tray or to the optional document finisher's output tray. 1 2 Press the MENU key. Press the 3 or 4 key repeatedly until Paper Handling > appears. Paper Handling > 3 Press the 2 key. 8 mm) 3-44 Chapter 3 Using the Operator Panel 1 2 Press the MENU key. 3 4 Press the 2 key. Press the 3 or 4 key repeatedly until Paper Handling > appears. Press the 3 or 4 key repeatedly until >Override A4/LT appears. Paper Handling > >Override A4/LT Off 3 Press the 2 key. >Stitch Adjust > appears. 5 Press the ENTER key. A blinking question mark (?) appears. >Stitch Adjust > >Override A4/LT ?>>A4/Letter appears. 6 >>A4/Letter 000 Select On or Off using the 3 or 4 key. 7 8 Press the ENTER key. 5 6 Press the 3 or 4 key to select A4/Letter, B4 or A3/ Ledger. When the desired paper size is displayed, press the ENTER key. A blinking cursor (_) appears under the value. Press the MENU key. The message display returns to Ready. Customizing Paper Type The following describes the procedure used to set a user-defined paper type for the printer. Eight custom user settings may be registered. After having been set, any of these may be called up when setting the paper type for a paper source. The paper weight and duplex path can be set (see Setting the Paper Weight on page 3-46, and Setting the Duplex Path on page 3-46) after selecting the paper type to be customized as follows. For how to reset the customized settings, see Resetting the Type Adjust on page 3-46. >>A4/Letter 000 7 8 9 Press the 3 or 4 key to increase or decrease, respectively, the value at the blinking cursor. Use the 2 and 1 keys to move the cursor right and left. Definable value: -057 to 057 When the desired value is displayed, press the ENTER key. The message display returns to Ready. 1 2 Press the MENU key. Press the 3 or 4 key repeatedly until Paper Handling > appears. Overriding A4 and Letter Size Difference This selects whether to enable or disable the difference between A4 size and Letter size. [. . . ] Select one or more mailboxes from the list of Defined Names. The Job Settings dialog box will appear. 8 Click the OK button. The Print dialog box is displayed again. The print job will be stored to the hard disk without printing. To print, use the Print VMB Data sub menu in the e-MPS menu at the printer operator panel and specify the virtual mailbox numbers. [. . . ]