User manual KYOCERA FS-C5015N

[. . . ] FS-C5015N FS-C5025N FS-C5030N Operation Guide Contents 1 Machine Parts Components at the Front of the Printer. 1-2 Components at the Left of the Printer . 1-3 Components at the Rear of the Printer . 1-4 Printing Operation Loading Printer Driver . [. . . ] There are 4 main charger units, one for each toner container. When performing the cleaning procedure, be sure to clean the main charger unit that corresponds to color of the toner container that was replaced. The following example explains the procedure to clean the main charger unit for the black toner container. Main Charger Units M C Y K 3-8 OPERATION GUIDE Maintenance 1 Open the left cover. Left Cover 2 First clean the main charger wire. Gently pull the wire cleaner knob out and push it back in. After cleaning, make sure you restore the wire cleaner knob to its home position. Wire Cleaner Knob NOTE: If the wire cleaner knob is not restored to its home position, a band will print along the length of the page. 3 Next, clean the main charger grid. Take the grid cleaner out of the toner kit. Take the grid cleaner out of the protective bag and remove the cap. Cap Grid Cleaner OPERATION GUIDE 3-9 Maintenance NOTE: The pad of the grid cleaner contains water. Clean the grid quickly so that the pad may not dry off. 4 Lift up slightly on the main charger unit and pull it out a short distance as shown in the figure below. Main Charger Unit 5 Attach the grid cleaner to the printer with the pad facing up. Grid Cleaner 3-10 OPERATION GUIDE Maintenance 6 Gently pull the main charger handle out and push it back in. After cleaning, make sure you restore the main charger unit to its home position. Main Charger Unit NOTE: If the main charger unit is not restored to its home position, the corresponding color will be printed over the whole page. 7 Remove the grid cleaner from the printer and discard it. The grid cleaner cannot be reused. Use the same procedure to clean the main charger units for the other toner containers. Proceed to the next section and clean the advanced beam array lenses. Cleaning the Advanced Beam Array Lenses If lines, etc. , appear on printed copies, the printouts appear dirty, or faint or blurred printouts are produced, clean the advanced beam array lenses. There is 1 lens on the main charger unit of each toner container. The following example explains the procedure to clean the lens on the main charger unit of the black toner container. OPERATION GUIDE 3-11 Maintenance 1 Grasp the tab of the green lens cleaner knob. Gently pull the lens cleaner knob out and push it back in. Repeat this 2 times. Lens Cleaner Knob 2 Push the lens cleaner knob back in completely. After cleaning, make sure you restore the lens cleaner knob to its home position. NOTE: If the lens cleaner knob is not restored to its home position, the corresponding color will be printed over the whole page. Use the same procedure to clean the lenses on the main charger unit of the other toner containers. 3-12 OPERATION GUIDE Maintenance 3 Once you are finished cleaning all 4 lenses, close the left cover. Cleaning the Paper Transfer Unit Print problems such as soiling of the reverse side of printed pages may occur if the paper transfer unit becomes dirty. To clean the paper transfer unit, you must use the cleaning cloth included in the toner kit. 1 While pulling the green paper transfer unit release lever, pull out the paper transfer unit. Paper Transfer Unit Release Lever Paper Transfer Unit OPERATION GUIDE 3-13 Maintenance 2 Wipe away the paper dust on the registration roller and the paper ramp using the wiper cloth included in the toner kit. Paper Ramp Transfer Roller (Black) Registration Roller (Metal) NOTE: Be careful not to touch the black transfer roller during cleaning as this may adversely affect print quality. 3 Push the paper transfer unit back in completely. 3-14 OPERATION GUIDE Maintenance Replacing the Waste Toner Box Replace the waste toner box when the Check waste toner box message is displayed. A new waste toner box is included with the toner kit. The printer will not operate without replacing the waste toner box. 1 Open the left cover. Left Cover 2 While holding the waste toner box, press the lock lever and then gently remove the waste toner box. Lock Lever NOTE: Remove the waste toner box as gently as possible so as not to scatter the toner inside. Do not let the opening of the waste toner box face downward. OPERATION GUIDE 3-15 Maintenance 3 Close the cap to the old waste toner box after removing the box from the printer. Cap Old Waste Toner Box 4 To prevent toner from spilling, put the old waste toner box in the plastic bag (contained in the toner kit) and discard it later according to the local code or regulations for waste disposal. Plastic Bag 5 Open the cap of the new waste toner box. Cap New Waste Toner Box 3-16 OPERATION GUIDE Maintenance 6 Insert the new waste toner box as shown in the figure below. When the box is set correctly, it will snap into place. New Waste Toner Box 7 Make sure that the waste toner box is correctly inserted and close the left cover. After replacing the toner containers and the waste toner box, clean the main charger units and the paper transfer unit. [. . . ] Turn RAM disk mode On from the operation panel. Insufficient printer memory to support the RAM disk system. Expand printer memory. 4-12 OPERATION GUIDE Troubleshooting Clearing Paper Jams If the paper jammed in the paper transport system, or no paper sheets were fed at all, the Paper jam message appears and the location of the paper jam (the component where the paper jam has occurred) is also indicated. The printer automatically goes off-line when this message is displayed. [. . . ]