User manual KYOCERA FS-C5020N

[. . . ] FS-C5020N FS-C5030N Basic Operation Guide Contents 1 Installation Unpacking the printer . 1-2 Installing the Toner Container and Waste Toner Box . 1-7 Machine Parts Components at the Front of the Printer. 2-2 Components at the Left of the Printer . [. . . ] After the cleaning is finished, however, the message does not automatically change to Ready. To restart printing, you must press [GO] and make the printer ready. · In either case, replace the toner container, see Toner Container Replacement on page 4-3. Replacing the Toner Container NOTE: During toner container replacement, temporarily put storage media and computer supplies (such as floppy disks) away from around the toner container. This is to avoid damaging media by the magnetism of toner. This section explains how to replace the toner containers. When replacing the toner container of any color, always replace the waste toner box at the same time. If this box is full, the printer may be damaged or contaminated by the waste toner that may spill over the box. NOTE: You do not have to turn printer power off before starting the replacement. Any data that may be under printing process in the printer will be deleted if you turn printer power off. To replace the toner container, first make sure of the color of the toner container requiring replacement. In this example, it is assumed that you are replacing the black toner container. 4-4 BASIC OPERATION GUIDE Maintenance 1 Open the top cover. Magenta (M) Cyan (C) Yellow (Y) Black (K) Top Cover 2 Pull the blue lock lever on the toner container forward towards the unlocked symbol. Lock Lever 3 Carefully remove the old toner container from the printer. BASIC OPERATION GUIDE 4-5 Maintenance 4 Put the old toner container in the plastic bag (contained in the toner kit) and discard it later according to the local code or regulations for waste disposal. Plastic Bag 5 6 Take the new toner container out of the toner kit. Shake the new toner container 5 or 6 times as shown in the figure in order to distribute the toner evenly inside the container. 7 Set the new toner container in the printer as shown in the figure below. 4-6 BASIC OPERATION GUIDE Maintenance 8 Push down on the top of the toner container to install it firmly in place. 9 Pull the blue lock lever on the toner container back towards the locked symbol as far as it will go. Lock Lever 10 11 Use the same procedure to replace the other color toner containers. Close the top cover. Proceed to the next section. BASIC OPERATION GUIDE 4-7 Maintenance Cleaning the Printer The following parts must be cleaned each time the toner container and waste toner box are replaced: · · · · Main charger wire Main charger grid Advanced beam array lens Registration roller In addition to this, it is recommended that the main charger wire and registration roller are cleaned periodically at least once a month. If lines, etc. , appear on printed copies, the printouts appear dirty, or faint or blurred printouts are produced, clean the advanced beam array lenses. Cleaning the Main Charger Unit The main charger units need to be cleaned periodically as they get contaminated after long usage. Each main charger unit comprises two main parts -- the wire and the grid -- which should be cleaned separately as explained below. There are 4 main charger units, one for each toner container. When performing the cleaning procedure, be sure to clean the main charger unit that corresponds to color of the toner container that was replaced. The following example explains the procedure to clean the main charger unit for the black toner container. Main Charger Units M C Y K 4-8 BASIC OPERATION GUIDE Maintenance 1 Open the left cover. Left Cover 2 First clean the main charger wire. Gently pull the wire cleaner knob out and push it back in. After cleaning, make sure you restore the wire cleaner knob to its home position. Wire Cleaner Knob NOTE: If the wire cleaner knob is not restored to its home position, a band will print along the length of the page. 3 Next, clean the main charger grid. Take the grid cleaner out of the toner kit. Take the grid cleaner out of the protective bag and remove the cap. Cap Grid Cleaner BASIC OPERATION GUIDE 4-9 Maintenance NOTE: The pad of the grid cleaner contains water. Clean the grid quickly so that the pad may not dry off. 4 Lift up slightly on the main charger unit and pull it out a short distance as shown in the figure below. Main Charger Unit 5 Attach the grid cleaner to the printer with the pad facing up. Grid Cleaner 4-10 BASIC OPERATION GUIDE Maintenance 6 Gently pull the main charger handle out and push it back in. After cleaning, make sure you restore the main charger unit to its home position. Main Charger Unit NOTE: If the main charger unit is not restored to its home position, the corresponding color will be printed over the whole page. 7 Remove the grid cleaner from the printer and discard it. [. . . ] The printer automatically goes off-line when this message is displayed. After removing jammed paper, the printer will re-start printing. Possible Paper Jam Locations The figure below explains the printer's paper paths including the options. The locations where paper jams might occur are also shown here, with each location explained in the table below. Paper jams can occur in more than one component on the paper paths. Face-up Tray PT-300/PT-301 Duplex Unit DU-300/DU-301 Paper Feeder PF-60 Paper jam message Paper jam location Description Reference page Paper jam Printer A Paper is jammed at paper cassette 1 or inside the printer. [. . . ]