User manual KYOCERA VI 200

[. . . ] No part of this material may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying, recording or by any information storage and retrieval system, without permission in writing from the Publisher. Legal Restriction On Copying · It may be prohibited to copy copyrighted material without permission of the copyright owner. · It is prohibited under any circumstances to copy domestic or foreign currencies. · Copying other items may be prohibited. Please read the instruction handbook before using the copier. [. . . ] 5 Repeat this for each title page number you want to appear on the right hand side. When setting more than 15 locations, touch the arrow key to move to the next page. Be sure to touch SET after each page number entry, up to a total of 30 entries. Option: Touch Booklet on the Chapter Insertion Setting No. To change the selection of paper tray for copying title pages, touch Copy Insertion on the screen. In this case, you can touch CHANGE OF THE INSERTION TRAY to change the currently selected paper tray displayed on the screen. 6 When all entries are made, touch OK to return to the Application Selection Screen. 7 Select additional copying features, as desired. 8 Touch OK to complete the setting and return to the Basic Screen. 10 Position originals FACE UP on the document feeder. 6-30. Option: Press [CHECK] to view the selection, and make the Proof copy, if desired; then touch EXIT to return to the Basic Screen. After copying is completed, touch Chapter on the Application Selection Screen or press [AUTO RESET] to release the mode and reset the machine. NOTES: 1 Entering "0" or the same page number twice will be ignored on the screen. 2 Chapter insertions occur in sequence even if original page numbers are entered out of sequence. 47 48 Booklet copying 47 45 2 48 1 3 . . . . . . . . . . . . . . 24 46 3 25 26 23 4 7 . . . . . . . . . . . . . . 1 5 45 47 2-sided originals 2 4 6 8 46 Application Selection Screen Booklet Mode Selection Screen 9-12 Applications 48 Applications Booklet (continued) 1 Load 11"x17" or 8. 5"x11"R copy paper in a tray. When selecting cover sheet mode (COVER WITH COPY SHEET or COVER WITH BLANK SHEET), load the same size paper in any other tray unless it is specified as Thick 2 or TAB of the paper type in the Key operator mode. on the Basic Screen to display the Application Selection Screen. 3 Touch Booklet to enter the Booklet Mode Selection Screen. 4 Touch NO COVER SHEET, COVER WITH COPY SHEET, or COVER WITH BLANK SHEET, as required. When a cover sheet is required, touch CHANGE OF THE COVERS TRAY to select the cover sheet tray source. Touch CHANGE OF THE OUTPUT MODE if you want to change the binding mode. 6 Select additional copying features, as desired. · When using the Reduce & shift mode or Page space function of Image shift, make the binding area in the center of copies. · Key operator can set the machine to position the page numbers automatically on the outside edges of the copy when using Booklet with Page Numbering in Stamp. 7 Touch OK on the Application Selection Screen to complete the selections and return to the Basic Screen. [. . . ] Follow instructions for adding toner. CALL FOR PM IS DISPLAYED IN MESSAGE AREA Contact your service representative for Preventive Maintenance. Troubleshooting 15-9 Troubleshooting Copying Hints (continued) APS SELECTS THE WRONG PAPER SIZE Paper guides must be adjusted exactly to the size of originals. IN MIXED ORIGINAL MODE, A MESSAGE TO LOAD A REQUIRED PAPER SIZE DISPLAYS, EVEN THOUGH THAT SIZE IS LOADED IN ONE OF THE TRAYS Paper sizes loaded in the trays must be consistent with the tray position size; otherwise, the tray key on the Basic Screen will blink. THE BASIC SCREEN DOES NOT DISPLAY SETTINGS AS DESCRIBED IN THIS MANUAL Check with the key operator, as Initial Settings may have been changed. PLEASE CHECK ORIGINAL This message displays when the copier detects a non-standard paper size on the platen glass. 1. 00 magnification will be selected automatically. If this message continues to display after selecting copy size, select 1. 00 magnification, even if it is already indicated, then press [START]. If desired, ask your service representative to enable the machine to default to 1. 00 magnification in this situation. SHEET INSERTION RESULT IS NOT AS EXPECTED Blank insertion: Be sure manuscript originals do not already include blank sheets in the locations designated for sheet insertion. [. . . ]