User manual LA CROSS TECHNOLOGY WS-9121U-IT

[. . . ] The outdoor temperature should then be displayed on the Temperature 44 4. station. If this does not happen after 2 minutes, the batteries will need to be removed from both units and reset from step 1. In order to ensure sufficient 915 MHz transmission however, there should be a distance of no more than 330 feet between the final position of the Temperature Station and the transmitter (see notes on "Positioning" and "915 MHz Reception"). Using Multiple Sensors with One Temperature Station 1. User shall remove all the batteries from the temperature station and transmitters and wait 60 seconds if setting has been done with one transmitter before. 45 2. [. . . ] BATTERY CHANGE: It is recommended to replace the batteries in all units every 12 months to ensure optimum accuracy of these units. 52 Please participate in the preservation of the environment. Return used batteries to an authorized depot. 53 FUNCTION KEYS Temperature Station: The Temperature Station has two easy to use function keys. SET/ CH key MIN/ MAX/ + key 54 SET/CH key (Setting/Channel) · Press and hold for about 3 seconds to enter the Manual setting mode. · Press shortly to toggle between different channel readings. MIN/MAX/+ key (Min/ Max temperature) Use to toggle between the minimum and maximum recorded readings of indoor & outdoor temperature. · Press and hold to reset minimum and maximum record (when min or max record is shown). · 55 LCD SCREEN AND SETTINGS: Time Outdoor Channel No. Indoor Temperature in °C Outdoor Temperature in °C Outdoor Reception Signal icon* Receiver Low battery indicator 56 Transmitter Low battery indicator * When the signal from the transmitter is successfully received by the Temperature Station, this icon will be switched on. (If not successful, the icon will not be shown on the LCD). User can therefore easily see whether the last reception was successful ("ON" icon) or not ("OFF" icon). On the other hand, the short blinking of the icon shows that a reception is being done at that time. For a better display clarity, the LCD screen is split into 3 sections, showing the information of time, indoor temperature and outdoor data. 57 Section 1 - TIME · Display of time (manually set). · Section 2 - INDOOR TEMPERATURE Display of indoor temperature. Section 3 - OUTDOOR TEMPERATURE · Display of outdoor temperature. 58 MANUAL SETTING: 12 / 24- HOUR TIME DISPLAY SETTING AND TEMPERATURE UNIT (°C/°F) SETTING User may choose to display the time in 12-hour or 24-hour mode: Note: When the time display is set as 12-hour mode, the temperature unit will be set to °F; when the time mode is in 24-hour format, the temperature unit will be set to °C. 59 1. 3. In normal display mode, press and hold the "SET/ CH" key for about 3 seconds. The "12h" or "24h" digit will be flashing. Press the "MIN/MAX/+" key to set the desired time display mode. Press shortly the "SET/ CH" key to advance to the MANUAL TIME SETTING. MANUAL TIME SETTING User shall manually set the time of the Temperature Station by the following steps: 1. The hour digit of the time display will be flashing. 60 2. 3. Press the "MIN/MAX/+" key to adjust the hour (press and hold to allow fast advance). Press "SET/ CH" key to confirm and go to the minute setting. Press the "MIN/MAX/+" key to adjust the minute (press and hold to allow fast advance). Press "SET/ CH" key once more to return to normal display. VIEWING THE MINIMUM AND MAXIMUM READINGS: User may consult the minimum and maximum recordings for indoor temperature, and outdoor temperature by following these steps: 1. Press the "MIN/MAX/+" key once to view the minimum indoor temperature and minimum outdoor temperature. 61 Minimum icon 62 2. Press the "MIN/MAX/+" key once more to view the maximum indoor temperature and maximum outdoor temperature. 63 Maximum icon RESETTING THE MINIMUM AND MAXIMUM READINGS: User may reset the minimum and maximum temperature data to the current value by the following steps: 1. Press the "MIN/MAX/+" key once to display the minimum data. Press and hold the "MIN/MAX/+" key for about 3 seconds to reset all the minimum / maximum data to the current values in a single action. Data of all outdoor and indoor sensor will be reset at the same time. 64 TEMPERATURE TRANSMITTER: The outdoor temperature is measured and transmitted to the Temperature Station every 16 seconds approximately. [. . . ] You may also have other rights specific to your State. Some States do no allow the exclusion of consequential or incidental damages therefore the above exclusion of limitation may not apply to you. For warranty work, technical support, or information contact: La Crosse Technology, Ltd 2809 Losey Blvd. La Crosse, WI 54601 Phone: 608. 782. 1610 Fax: 608. 796. 1020 82 e-mail: support@lacrossetechnology. com (warranty work) sales@lacrossetechnology. com (information on other products) web: www. lacrossetechnology. com 83 Questions? [. . . ]