User manual LA CROSS TECHNOLOGY WT-5350

[. . . ] WT-5350 Radio Controlled Projection Alarm Instruction Manual RADIO CONTROLLED FCC ID: OMO-01RX (receiver) DATE THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: 1. THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND 2. THIS DEVICE MUST ACCEPT INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION. AL/SEL MODE/ + PROJECTION R Contents Language English Français Spanish Page 2 31 61 TABLE OF CONTENTS Topic Inventory of Contents About WWVB Quick Set-Up Guide Detailed Set-Up Guide Battery Installation Program Mode Programming Sequence Function Buttons Time Zone Setting Time Setting Date Setting 12/24-Hour Mode DST (Daylight Saving Time) Setting Page 4 5 6 7 10 11 11 12 13 14 15 Features & Operations Features Radio-Controlled Time and Date Projection EL. [. . . ] Hold down the "MODE/+" button for 2 seconds (the selected time zone will flash), press the "AL" button three times until the year flashes. Press the "MODE/+" button to select the year. Press the "AL" button to confirm the year and move to the month setting. Press the "MODE/+" button to select the month. Press the "AL" button to confirm the month and move to the day setting. Press the "MODE/+" button to select the day. Press the "AL" button to confirm the day and move to the 12/24 Hour display setting, or press the "SNOOZE" button to confirm the date and return to the display mode. Hold down the "MODE/+" button for 2 seconds (the selected time zone will flash), press the "AL" button six times until " :12" flashes in the time display. 2. Press the "MODE/+" button to toggle between 12 and 24-hour time display. Press the "AL" button to confirm the time display setting and move to the Daylight Saving Time setting, or press the "SNOOZE" button to confirm the time display setting and return to the display mode. DAYLIGHT SAVING TIME Note: The DST default is "On", meaning that the WWVB will automatically change the time according to Daylight Saving Time in the spring and fall. For areas that do not recognize DST changes (Arizona and parts of Indiana) turn the DST to "OFF". 1. Hold down the "MODE/+" button for 2 seconds (the selected time zone will flash), press the "AL" button seven times until "ON" flashes in the date display area and "DST" flashes above the U. S. Press the "MODE/+" button to toggle between "ON" and "OFF" modes. P. 15 GB P. 14 GB 3. Press the "AL" button to confirm the DST setting and complete the setup. The projection alarm will automatically search for the time signal upon initial set-up and every night. When the signal is being received, there will be a "tower" icon flashing to the right of the time display. 3. When the time signal has been received successfully, the tower icon will remain steady until midnight. The NIST (National Institute of Standards and Technology-Time and Frequency Division) WWVB radio station is located in Ft. Collins, Colorado, and transmits the exact time signal continuously throughout the United States at 60 kHz. The signal can be received up to 2, 000 miles away through the internal antenna in the Projection Alarm. Due to the nature of the Earth's Ionosphere, reception is very limited during daylight hours. [. . . ] To receive warranty service, the purchaser must contact La Crosse Technology, Ltd for problem determination and service procedures. Warranty service can only be performed by a La Crosse Technology, Ltd authorized service center. The original dated bill of sale must be presented upon request as proof of purchase to La Crosse Technology, Ltd or La Crosse Technology, Ltd's authorized service center. La Crosse Technology, Ltd will repair or replace this product, at our option and at no charge as stipulated herein, with new or reconditioned parts or products if found to be defective during the limited warranty period specified above. [. . . ]