User manual LA CROSSE TECHNOLOGY TX29U-IT

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual LA CROSSE TECHNOLOGY TX29U-IT. We hope that this LA CROSSE TECHNOLOGY TX29U-IT user guide will be useful to you.

Lastmanuals help download the user guide LA CROSSE TECHNOLOGY TX29U-IT.


Mode d'emploi LA CROSSE TECHNOLOGY TX29U-IT
Download
Manual abstract: user guide LA CROSSE TECHNOLOGY TX29U-IT

Detailed instructions for use are in the User's Guide.

[. . . ] Insert the batteries to the second transmitter as soon as the outdoor temperature readings from the first transmitter are displayed on the temperature station. Note: User shall insert the batteries into the second transmitter within 45 seconds of reception of the first transmitter. The outdoor temperature from the second transmitter and the "channel 2" icon should then be displayed on the Temperature station. If this does not happen after 5 minute, the batteries will need to be removed from all the units and reset from step 1. Insert the batteries to the third transmitter as soon as the "channel 2" icon and outdoor data are displayed on the temperature station. [. . . ] Observing the correct polarity install 2 AA, Alkaline batteries. The batteries will fit tightly (to avoid start-up problems make sure they do not spring free). Replace the battery cover by sliding upwards. Note: · · · If the signal reception is not successful on the first frequency of 915MHz for 45 seconds, the frequency is changed to 920MHz and the learning is tried for another 45 seconds. If it is still not successful the reception is tried for 45 seconds on 910MHz. This will also be done during resynchronization. Detailed Set up procedures of the Temperature Station and the Transmitter refer to the main operation manual of WS-9021U or 9640U. MOUNTING THE TEMPERATURE TRANSMITTER The Temperature transmitter can be mounted onto a wall with the use of screws MOUNTING WITH SCREWS SETTING UP When one transmitter is to be used 1. First, insert the batteries to the temperature transmitter (see "Battery Installation" below). Within 2 minutes of powering up the transmitter, insert the batteries to the Temperature Station (see "Battery Installation" below). Once the batteries are in place, all segments of the LCD will light up briefly. Following the indoor temperature and the time as 12:00 will be displayed. If they are not shown in LCD after 60 seconds, remove the batteries and wait for at least 60 seconds before reinserting them. Once the indoor data is displayed user may proceed to the next step. After the batteries are inserted, the Temperature Station will start receiving data signal from the transmitter. The outdoor temperature should then be displayed on the Temperature station. If this does not happen after 5 minutes, the batteries will need to be removed from both units and reset from step 1. In order to ensure sufficient 915 MHz transmission however, there should be a distance of no more than 330 feet (100 meters) between the final position of the Temperature Station and the transmitter. Adding additional remote transmitters (using more than 1 transmitter) 1. 5. Remove the mounting bracket from the Temperature transmitter. Place the mounting bracket over the desired location. Through the two screw holes of the bracket, mark the mounting surface with a pencil. Screw mounting bracket onto the mounting surface. [. . . ] Warranty service can only be performed by a La Crosse Technology, Ltd authorized service center. The original dated bill of sale must be presented upon request as proof of purchase to La Crosse Technology, Ltd or La Crosse Technology, Ltd's authorized service center. La Crosse Technology, Ltd will repair or replace this product, at our option and at no charge as stipulated herein, with new or reconditioned parts or products if found to be defective during the limited warranty period specified above. All replaced parts and products become the property of La Crosse Technology, Ltd and must be returned to La Crosse Technology, Ltd. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE LA CROSSE TECHNOLOGY TX29U-IT

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets...
In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.

Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual LA CROSSE TECHNOLOGY TX29U-IT will begin.

Search for a user manual

 

Copyright © 2015 - LastManuals - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.

flag