User manual LARSON WOOD CORE RETRACTABLE SCREEN

[. . . ] Wood-Core Series Retractable Screen Storm Door INSTALLATION INSTRUCTIONS Before You Get Started. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 1 Installation Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Pages 2­7 Closure Installation Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Pages 6­7 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 8 Warranties. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 5 General Care and Maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 9 Visit our web site at www. larsondoors. com Congratulations!You've purchased a quality-built wood core storm/screen door from Larson. Please take a moment to fill out and mail in your product warranty card for years of trouble-free service. NOTE: Modification of door will void warranty. [. . . ] To install bottom closer, hold assembly level 1" above the expander and hold jamb bracket 1/4" from storm door. Mark and attach as shown in steps 1, 2, and 3. NOTE: Bottom closer may need to be applied over the door expander in some cases. Slide hold-open washer over flanges toward cylinder on closer. 6 202220586 RETRACTABLE WOOD-CORE DOOR BRACKET INTERIOR VIEW LOOKING OUT CLOSER DOOR BRACKET SCREWS 2 CLOSER MODELS: 11/2" ABOVE WINDOW (TOP CLOSER) 1" ABOVE EXPANDER (BOTTOM CLOSER) FIGURE 3 #10 x 5/8" ROUND HEAD #10 x 1-1/2" ROUND HEAD LONG PIN SHORT PIN 2 Controlled Latching Power Feature 3 Wind Safety Chain Installation Installed as directed, with door bracket connected to the FRONT hole of closer, the door will accelerate its closing speed in the last few inches of travel. This attachment position is recommended when the glass storm panel is in place. If a smoother, quieter closing action is desired, hold door open about 8" with hold-open washer. Move in from door bracket and relocate in closer REAR hole. This position is normally used when the screen panel is in place. On two closer models, adjust each closer individually (with the other closer disconnected from the door) to the closing speed sufficient to latch the door. The closing speed for each closer should be the same. FIGURE 4 NOTE: Some models do NOT come with a safety chain. To attach safety chain, position the header bracket on the head jamb 18" in from the hinge side of the door frame and 1-1/2" back from the front of jamb (Figure 5). Mount this bracket at approximately 45 degrees (pointing towards door bracket when door is open). Mark location of the holes and drill two pilot holes with a 1/8" bit about 3/8" deep. Mount header bracket with two #10x3/4" round head screws (Figure 6). Mount door bracket on the inside door surface 1-1/2" from top edge of the door and 19" from hinge edge of the door in a horizontal position. Use two (2) #12x5/8" round head screws (Figure 7). If greater opening is desired, mount each bracket slightly closer to hinge edge of door. To allow full opening or removal of door, detach chain from bracket. To attach hold-up spring, close the door and thread one end of the spring onto the lowest link of the chain (Figure 8). Swing wind chain up towards hinge side of door and attach hold-up spring to head jamb with doublehead nail about 3" in from side jamb FIGURE 6 FIGURE 7 (Figure 8). Hold-up spring should not be stretched over 1/4" when door is closed. #10 x 3/4" ROUND HEAD #10 x 5/8" ROUND HEAD REAR HOLE CLOSER FRONT HOLE ADJUSTING SCREW To change closing speed, turn screw on the end of closer tube clockwise for slower and counter clockwise for faster. (Figure 4) See Troubleshooting, Symptom E for more adjustment information. FIGURE 5 HEADER BRACKET HEAD JAMB DOOR BRACKET 1-1/2" DOUBLE HEADED NAIL HOLD UP SPRING /2 1-1 " FIGURE 8 19" HEAD JAMB 18" 3" 11/2" (2) #10x3/4" ROUND HEAD SCREWS " 18 SAFETY CHAIN (2) #10x5/8" ROUND HEAD SCREWS DOUBLE HEADED NAIL 19" INSIDE DOOR FRAME HINGE SIDE JAMB INSIDE OF DOOR HOLD-UP SPRING LOWEST LINK INTERIOR VIEW TOP Z-BAR (DRIP CAP) SCREW COVER NOTE: Some models have screw covers, some do not. Z-Bar Screw Cover Installation 1. [. . . ] As with all brass products, tarnishing will occur. Without proper care, brass can become stained so heavily that cleaning cannot totally remove the stain. In extreme cases of neglect, pitting can occur. Larson locksets and deadbolts have a clear coat finish. [. . . ]