User manual LASERLINE 862TL

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual LASERLINE 862TL. We hope that this LASERLINE 862TL user guide will be useful to you.

Lastmanuals help download the user guide LASERLINE 862TL.


Mode d'emploi LASERLINE 862TL
Download
Manual abstract: user guide LASERLINE 862TL

Detailed instructions for use are in the User's Guide.

[. . . ] Motorcycle Alarm Systems 862 cod. : ISUT862T FILENAME: ISUT862T. P65 862TH - 862TL INSURANCE APPROVED MOTORCYCLE ALARM/IMMOBILISER USER GUIDE GB These Laserline systems are manufactured from the highest quality components to ensure a long trouble free operating life and comply with the British insurance industry's criteria for motorcycle security for Category MC1 product. PRODUCT COMPLIANCE Laserline 862TH/862TL - Combined Alarm/Immobiliser MC1 - MIRRC Test No. TMC1 177/1002 These instructions are intended to familiarise you with their simple operation. Note: There are 2 versions of the 862T, the only difference between the units are the internal inclination sensors. [. . . ] To translate the pin code use the following example: For the numbers 5 !6 0 5 4 12 n° of corresponding flashes n° 5 consecutive LED flashes n° 6 consecutive LED flashes n° 10 consecutive LED flashes n° 5 consecutive LED flashes n° 4 consecutive LED flashes !Pause On the example, the Pin Code to note at the end of these instructions would be 5 6 0 5 4. It is imperative to note on a piece of paper this Emergency Pin Code, if it is different from the original pin code displayed in the rear of these instructions. This pin code must then be stored in a secure location. Note: if you intend to leave these instructions on the motorcycle, the pin code in the back of these instructions should be removed for safe keeping. This emergency code is derived from the last remote control/garage sensor memorised when you selflearn a new remote control. If you want to change the pin code from the original code, you may have to follow the self-learning procedure more than once alternating the first remote control until a new pin code is given. HOW TO DISARM THE ALARM USING THE EMERGENCY PIN CODE If the remote control does not work correctly, then the following emergency procedure may be used to disarm the security system temporarily: 1) With the alarm armed or passively immobilised, cause an alarm condition by turning the ignition key to the ON position until the alarm starts to sound. 2) When the alarm starts to sound turn ignition key OFF. 3) The alarm will sound for 30 seconds and will then stop sounding. Then the LED located on the motorcycle will come ON (illuminate). Within 4 seconds, switch ON/OFF the ignition key for 1 second. 4) After 2 seconds, the LED/Alarm will start to flash/beep. The alarm is now ready to accept the Emergency Pin Code, displayed at the end of these instructions. 5) For each digit of the pin code, the LED/Alarm will flash/beep 10 times. You must switch ON the ignition key for 1 second at the same time of the corresponding flash/beep. Turn OFF the ignition key and start to count the next digit value and repeat until all 5 pin code digits have been inputted. 6) If the emergency pin code is correct, the alarm will disarm signalled by one flash of the indicator lights and one acoustic tone. If not, the alarm will remain armed and steps 1-5 will have to be repeated again. Once the alarm is disarmed, turn the ignition key ON within 30 seconds to enable starting of the engine. If the ignition is not switched ON the alarm system automatically enters the "SELFLEARNING OF REMOTE CONTROL CODES" function at step 5. This allows you to program new remote controls if all remotes are lost and to clear the "secret code" if you have forgotten your sequence. 13 EXAMPLE: the code to be inserted is 5 6 0 5 4. [. . . ] If product is repaired by a non authorised installer the product will cease to be covered by the warranty. CONSUMER SUMMARY All warranties are limited to the duration of this warranty. This is the complete warranty and no other express or implied warranty is valid. Nothing in this warranty shall affect your statutory rights. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE LASERLINE 862TL

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets...
In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.

Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual LASERLINE 862TL will begin.

Search for a user manual

 

Copyright © 2015 - LastManuals - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.

flag