User manual LEICA TPS1100

[. . . ] Leica TPS1100 Professional Series User Manual Version 2. 2 English Electronic total stations Congratulations on your purchase of a TPS1100 Professional Series instrument. This manual contains important safety directions (refer to chapter "Safety directions") as well as instructions for setting up the product and operating it. Read carefully through the User Manual before you switch on the instrument. 2 TPS1100 - User Manual 2. 2. 1en Product identification The instrument model and the serial number of your product are indicated on the label in the battery compartment. Enter the model and serial number in your manual and always refer to this information when you need to contact your agency or authorized service workshop. Type: Serial number: Software version: Language: TPS1100 - User Manual 2. 2. 1en 3 Product identification Symbols used in this manual The symbols used in this User Manual have the following meanings: DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. [. . . ] The other parameters are set to "0. 00". System functions 72 TPS1100 - User Manual 2. 2. 1en MC Distance corrections ppm, continued Refraction correction The refraction correction is taken into account during the calculation of the height difference. \ REFRACTION CORR. (k) : ON 0. 13 Reduced distance corrections ppm For standard applications the distance is corrected only on account of atmospheric influences. The geometrical correction and the projection distortions are set to "0. 00". Heights are reduced with the standard refraction coefficient Activate the function "PPM Atmospheric" from the dialog "Function Selection". QUIT \ PPM Corrections Enter your correction values Atm. pressure : Temperature : 1013. 3 mbar 12. 0 °C -0. 0 QUIT Measurement & recording (REC) MEAS\ Measurement & Record Point Id : 1 Attrib. : 1. 500 Hz :286°55'50" V : 91°16'20" Horiz. Dist. : ----ALL DIST REC : : : : MC m m m m m m 6 10 12 21 26 SetHz >DISP ----------------- MC Elev. Diff. East North Elev. INPUT Del B I<>II INDIV QUIT MC CONT DEFLT The data shown above represent the standard display mask. The recorded measurement-block corresponds to the active recording template. The last measured distance is also recorded. Sets the refraction coefficient to standard values. ppm total CONT : Input of air pressure and temperature or Input of ppm value. The values for pressure and temperature are erased. TPS1100 - User Manual 2. 2. 1en 73 System functions Measuring distances and angles separately (DIST + REC) This procedure offers the option of realigning the telescope on another point after measuring the distance and before measuring the angle. In this way two points can be used for measurements of angle and distance. It is therefore possible to record inaccessible points, e. g. house corners, fences surrounded by hedges. For calculations which depend on distance, the V-angle after completion of the distance measurement is used, along with the current Hz-direction. Consequently, calculated heights and height differences are retained and the coordinates for easting and northing which correspond to the new Hz direction are recalculated using the last-measured distance. The V-angle displayed corresponds to the position of the telescope on completion of the distance measurement. The V-angle is not altered until the measurement is recorded for a new distance is measured. When distances, heights, or height differences are displayed as empty fields (i. e. -----), the V-angle is continuously displayed and updated. If, after the distance has been measured, changes are made to the target-point data which have an influence on the distance measured or on the height and height difference (e. g. ppm, prism constant, reflector height, refraction coefficient), the dependent data will be correspondingly re-computed. MEASURING DISTANCE STORING DATA 1000QS37 1000QS36 System functions 74 TPS1100 - User Manual 2. 2. 1en Measuring distances and angles together with storage (ALL) Hz-angle measurement is carried out after the distance has been measured. [. . . ] 79, 80 Station setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66 Storage concept . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Storing station data (REC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75 Switch between Fast measurement/ Rapid Tracking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]