User manual LENCO MC-140

[. . . ] INSTRUCTION MANUAL MICRO MUSIC CENTRE WITH CD PLAYER, PLL RADIO AND USB/SD/MMC INTERFACE MC-140 IMPORTANT NOTES INTRODUCTION Thank you for buying this product. Please read through these operating instructions, so you will know how to operate your equipment properly. Store the manual in a save place for future reference after you finished reading the instructions. Put it away in a safe place for future reference. CAUTION Use of controls or adjustment or performance of procedures other than those specified in this manual may result in hazardous radiation exposure. DANGER Invisible laser radiation when open and interlock failed or defeated. [. . . ] Press MEMORY-UP or MEMORY-DOWN button to listen to the stored station directly. USING THE CD/MP3 Discs for Playback This system can playback all digital audio CD/MP3, finalized digital audio CD-Recordable (CD-R) discs, finalized digital audio CD-Rewritable (CD-RW) discs and CD-DA format digital audio CD/CDR/ CD-RW discs. LOADING A DISC Press the FUNCTION switch to select CD playing mode. Open the CD door, OPEN will be shown on the display. Place an audio CD/MP3 disc into the tray with the label side facing up. The display will show CD READ , then the total number of tracks, album (if a MP3 disc contains several albums) and STOP will appear on the display after several seconds. To remove the CD, press OPEN to open the CD compartment lid, the display will show OPEN . Take the CD by its edges and carefully lift it out the device. Note: Make sure the disc is stopped before open the CD compartment. To ensure a good system performance; you need to wait until the disc tray completely reads the disc before proceeding. If no disc loaded into the compartment, or the disc is unreadable, the display will show NO DISC . Press PLAY/PAUSE button to start the playback. To interrupt the playback, press the PLAY/PAUSE button again. The elapsed time will flash on and off in the display. To resume playback, press PLAY/PAUSE button again. To stop the playback, press the STOP button. The total number of tracks and playing time (only Audio CDs) will appear in the display (MP3 shows number or folders and tracks). SELECTING A DESIRED TRACK/PASSAGE To select a desired track CD: Press CD SKIP BACK/FORWARD & RADIO TUNING UP/DOWN button repeatedly in stop mode or during playing until the desired track appears on the display. MP3: Press the MEMORY UP / ALBUM + button repeatedly in stop mode or during playing to select desired album. Then press CD SKIP BACK/FORWARD & RADIO TUNING UP/DOWN button to select desired track. To search for a particular passage during playback (track scanning at high speed) Press and hold CD SKIP BACK/FORWARD & RADIO TUNING UP/DOWN button to scan the current playing track at high speed until desired point (passage), then release the button for normal playback mode. Playback will start again from this point. 5 PROGRAM TRACKS Program tracks of disc are possible when playback is stopped. Up to 64 tracks can be stored in the memory in any order. In stop mode, press MEMORY button to enter program setting, the display will show 00 P -- 01. 2 Press the CD SKIP BACK/FORWARD & RADIO TUNING UP/DOWN button to select the first desired track to be programmed. [. . . ] Note: Switch the unit to CARD-USB or CD/MP3 playing mode, follow the above steps to proceed PROGRAM TRACKS ON SD/MMC CARD or ON MP3 disc. TO FIND A DESIRED TRACK (not for CD) To listen to the desired track, press the FIND/ST/ESP button once to search FILE, press again to search ALBUM, press the MEMORY button, the track number within this album is flashing, press the CD SKIP BACK/FORWARD & RADIO TUNING UP/DOWN button to select the desired track, then press PLAY/PAUSE button to start playback. REMOTE HANDSET LOADING THE BATTERIES INTO THE REMOTE HANDSET Open the battery compartment cover. Insert two AAA batteries (not included) as indicated inside the battery compartment. Close the cover. REMOTE CONTROL OPERATION You can control the system with the provided remote controller. Inset two (AAA/UM-4) batteries correctly so that the + and polarities match the polarity diagrams inside the battery compartment. [. . . ]