User manual LENCO TFT-920

[. . . ] The documentation will assist you in obtaining the best equipment performance. Save this manual for later use. Important Notice It is unlawful in most jurisdictions for a person to drive a motor vehicle which is equipped with a television viewer or screen that is located in the motor vehicle at any point forward of the back of the driver's seat, or that is visible, directly or indirectly, to the driver while operating the vehicle. In the interest of safety, this system should never be installed where it will be visible, directly or indirectly, by the operator of the motor vehicle. Safety Precaution For safety reasons, when changing video media, it is recommended that the vehicle is not in motion, and that you do not allow children to unfasten seat-belts to change video media or make any adjustments to the system. Enjoy your entertainment system but always remember: safety of all passengers remains the number one priority. -1- Important Safety Instruction The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of un-insulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric to persons. [. . . ] Please take out the battery when the remote control is not used for a long time, in order to avoid damage to the remote control caused by possible liquid leakage. - 10 - Rechargeable Battery About Rechargeable Battery Pack Your portable DVB-T receiver can be connected with a lithium polymer rechargeable battery that attaches to the bottom of the unit. Your new battery should be fully charged before initial use. Charging time is normally about 4 hours. A fully charged battery delivers about 2. 5-3 hours of use. If the battery will not be used for a long period of time, first fully charge the battery prior to storage. Working conditions and precautions of the battery · · · · Battery should only be used and charged when temperatures are between 32ºF and 80ºF. (0ºC - 27ºC) Never put the battery in fire or water. Do not expose the battery to high temperatures or store in hot, sunny places. Maintain well-ventilated conditions around the product, avoiding heat. Don't put the product on bed, sofa or anything that may block ventilation to the product. · · Do not open the battery. You can adjust the items in this menu to compensate for environment influences or to setup the screen to your own preference. TV Setup Menu Press the TV SETUP button twice to enter the TV setup menu, as shown below: TV SETUP SYSTEM CHANNEL FINE SKIP MANUAL AUTO PAL B/G 28 487. 25UHF OFF OFF In the TV Setup menu, press the SELECT or 1. Channel Press the SELECT or the channel number. buttons to select item. buttons to select buttons to select SYSTEM, press the buttons to select CHANNEL, press the buttons to select - 18 - TV Setup 3. Fine Tuning When reception quality is less than desirable, you can improve this with the fine tuning function. Press the SELECT or buttons to select FINE, press the button to start fine tuning, when video and audio are at their best, stop the fine tuning and the program will be stored automatically. Skip Press the buttons to select ON, the channel will be skipped when using the CH-/+ to select channels. Manual Searching Press the SELECT or buttons to select MANUAL, press the buttons to start searching, press the buttons again to stop searching, the programs searched will be stored automatically. Auto Searching Press the SELECT or buttons to select AUTO, press the buttons to select ON. It will take a few minutes, when searching is finished, it will exit and return to channel 1. All found programs will be placed in sequence. Function Setup Menu Press the TV SETUP button three times to enter the Function Setup menu, as shown here: FUNCTION LANGUAGE TIME OFF DEFAULT ENGL ___ In the Function setup menu, press the SELECT or 1. Language Press the SELECT or select different languages. buttons to select item. buttons to select LANGUAGE, press the buttons to 2. [. . . ] There are a few more options you can use with every program: Select the program and press the button to enter, and then use the button to select Add, Modify, Delete, Lock/Unlock or move. See the picture below: Select Add to add new programs into the list. Follow the procedure mentioned above to add programs. Select Modify to modify the information of the program. [. . . ]