User manual LENOVO D185 WIDE LCD MONITOR

[. . . ] D185 Wide LCD Monitor User's Guide Product numbers 6207-HB1 First Edition (Oct 2008) (c) Copyright Lenovo 2008. LENOVO products, data, computer software, and services have been developed exclusively at private expense and are sold to governmental entities as commercial items as defined by 48 C. F. R. 2. 101 with limited and restricted rights to use, reproduction and disclosure. LIMITED AND RESTRICTED RIGHTS NOTICE: If products, data, computer software, or services are delivered pursuant a General Services Administration "GSA" contract, use, reproduction, or disclosure is subject to restrictions set forth in Contract No. GS-35F-05925. Contents Safety information . [. . . ] The words "DDC/CI disable"or "DDC/CI enable" shows on the screen. 2-4 D185 Wide LCD Monitor User's Guide Table 2-2. OSD functions OSD Icon on Main Menu Controls and Adjustments (Analog) Controls and Adjustments (Digital) Same as Analog Submenu Description Adjusts overall brightness Brightness/ Contrast Brightness Adjusts difference between light and dark areas Contrast Moves the image left or right Controls Locked not required for digital input Image Position Horizontal Position Moves the image up or down Automatically optimizes the image Vertical Position Image Setup Automatic Manually optimizes the image. See "Manual image setup" on page 3-4 · · · Clock Phase Save Same as Analog Manual Adjusts intensity of red, green, and blue Image Properties Color Preset mode · · · · Neutral sRGB Reddish Bluish Custom · · · · · Scaling · Red: Increases or decreases the saturation of 'red' in the image Green: Increases or decreases the saturation of 'green' in the image Blue: Increases or decreases the saturation of 'blue' in the image Save: Saves the custom color choices Original AR Full screen Chapter 2. 2-5 Table 2-2. OSD functions OSD Icon on Main Menu Controls and Adjustments (Analog) Controls and Adjustments (Digital) Same as Analog Submenu Description Input video signal This monitor can accept video signals through two different connectors. Most desktop computers use a D-SUB connector. Select digital among OSD Controls when you use DVI connector - Selects D-SUB (Analog) - Selects DVI (Digital) Optimize screen for specific tasks NOVO VISION Shows resolution, refresh rate, and product details Options Information Note: This screen does not allow any changes to the settings This section lists the languages supported by your monitor Note: The language chosen only affects the language of the OSD. It has no effect on any software running on the computer Menu position adjusts menu location on the screen Default Default returns the menu position to the default settings Custom · Horizontal: Changes the horizontal position of the OSD · Vertical: Changes the vertical position of the OSD Same as Analog Same as Analog Menu Language Menu Position Factory Default Accessibility · Save · Cancel · Reset Resets monitor to the original factory settings Controls button and menu settings for accessibility preferences Button repeat rate: Select or to change · Off · Default · Slow Menu time out: Sets the length of time the OSD will remain active after the last time a button is pressed 2-6 D185 Wide LCD Monitor User's Guide Selecting a supported display mode The display mode the monitor uses is controlled by the computer. Therefore, refer to your computer documentation for details on how to change display modes. The image size, position and shape might change when the display mode changes. This is normal and the image can be readjusted using automatic image setup and the image controls. Unlike CRT monitors, which require a high refresh rate to minimize flicker, LCD or Flat Panel technology is inherently flicker-free. Note: If your system has previously been used with a CRT monitor and is currently configured to a display mode outside the range of this monitor, you may need to reattach the CRT monitor temporarily until you have re-configured the system; preferably to 1366x768 at 60 Hz, which is the Native Resolution Display mode. The display modes shown below have been optimized at the factory. Factory set display modes Addressability 640 x 480 700 x 570 640 x 350 720 x 400 800 x 600 1024 x 768 1360 x 768 1366x 768 Refresh rate 60 Hz 66Hz 72 Hz 75 Hz 50 Hz 70 Hz 70Hz 60 Hz 72Hz 75Hz 60Hz 70 Hz 75 Hz 60 Hz 60 Hz Chapter 2. 2-7 Understanding power management Power management is invoked when the computer recognizes that you have not used your mouse or keyboard for a user-definable period. There are several states as described in the table below. For optimal performance, switch off your monitor at the end of each working day, or whenever you expect to leave it unused for long periods during the day. Power indicator State On Power Indicator Blue Screen Normal Blank Press a key or move the mouse There may be a slight delay before the image reappears Note: Standby also occurs if there is no image output to the monitor Off Off Blank ENERGY STAR ENERGY STAR Restoring Operation Compliance Standby/Suspend Amber 2-8 D185 Wide LCD Monitor User's Guide Caring for your monitor Be sure to turn off the power before you perform any maintenance on the monitor. Do not: · · · · · Do: · · Lightly dampen a soft cloth with water and use this to gently wipe the covers and the screen. Remove grease or finger marks with a damp cloth and a little mild detergent. Apply water or liquid directly to your monitor. Use flammable cleaning materials to clean your monitor or any other electrical equipment. Touch the screen area of your monitor with sharp or abrasive items. [. . . ] I will choose the driver to install" option, and then click Next. Click the Browse button and navigate to the following directory: X:\Monitor Drivers\Windows XP (where X is the drive letter designator for the CD-ROM drive). Select the "D185wA . inf" file and click the Open button. The files will be copied from the CD to your hard disk drive. [. . . ]