User manual LEXIBOOK MD1600

[. . . ] Color profile: Generic CMYK printer profile Composite Default screen Important note -- emergency calls The MD 1600 is not designed for making emergency calls when the mains power fails. So you should make alternative arrangements for access to Emergency Services. (This means that you should also have a basic phone that does not need mains power, connected to your line so that you can make calls during a power failure. ) If you need help . . . The Binatone Help Line is available from 9. 00 am to 5. 00 pm, Monday to Friday, on 01325 304 473 Unpacking your MD 1600 In the box are: the cordless handset (two handsets with a Twin system, three with a Triple system, four with a Quad system) the base unit rechargeable batteries or a battery pack, and a battery compartment cover for the handset a telephone line cable a mains power lead and adapter If you have an MD 1600 Twin, Triple or Quad system, you should also have: one, two or three charger pods a mains power lead and adapter for each one Keep the packaging materials in a safe place in case you later need to transport the unit. Keep your sales (till) receipt, which is your guarantee. E:\Binatone2003\MD1600\MD1600_03. vp 09 June 2003 15:20:00 Color profile: Generic CMYK printer profile Composite Default screen Where to find it UP and DOWN buttons Press to display the last 10 numbers you dialled. [. . . ] When you press any key except the MENU button, the programmed number will be dialled out automatically. ! With BabyCall turned on, it is not possible to make emergency calls, unless you have programmed an emergency number such as 999 as the BabyCall number. But remember that the number you have programmed will be dialled out automatically when any key is pressed. Before turning BabyCall on, you must first program the telephone number. To programme 1 the BabyCall number Press the MENU button The display shows phonebk Press the o button FOUR times The display shows babycall Press the OK button Press the o button ONCE OR TWICE until the display shows number?Press the OK button Key in the number (up to 20 digits) If you make a mistake, press the C button to delete digits from the display. 2 3 4 5 6 7 8 Press the OK button to confirm Press the MENU button to go back into standby mode 28 E:\Binatone2003\MD1600\MD1600_03. vp 09 June 2003 15:22:12 Color profile: Generic CMYK printer profile Composite Default screen Babysitter's Call (BabyCall) To change the BabyCall number 1 2 3 Go to step 28 OK Press and hold the C button to clear the display Key in the new number and press the OK button Press the MENU button to go back into standby mode Press the MENU button The display shows phonebk Press the o button FOUR times The display shows babycall Press the OK button The display shows off Press the o button The display shows on Press the OK button As long as babycall is shown on the display, pressing any key will automatically make a call to the BabyCall number. 4 To turn BabyCall ON 1 2 3 4 5 Binatone Help Line: 01325 304 473 29 E:\Binatone2003\MD1600\MD1600_03. vp 09 June 2003 15:22:12 Color profile: Generic CMYK printer profile Composite Default screen Babysitter's Call (BabyCall) To turn 1 BabyCall OFF Press the MENU button The display shows babycall Press the OK button The display shows on Press the r button The display shows off Press the MENU button to go back into standby mode 2 3 4 30 E:\Binatone2003\MD1600\MD1600_03. vp 09 June 2003 15:22:12 Color profile: Generic CMYK printer profile Composite Default screen Resetting the system !! If you reset the system, you will lose all stored information (including numbers in memory) and all features will return to their default settings. While you are resetting the system, you should disconnect the telephone line cord from the back of the base unit, so you won't be interrupted by incoming calls. There are two methods of resetting the system. You'll only need the second one if you have set a PIN (see page 25) and forgotten it. The PIN will be reset to 0000. Reset with the PIN 1 2 3 4 5 6 Press the MENU button The display shows phonebk Press the o button twice The display shows base Press the OK button The display shows volume Press the o button NINE times The display shows default Press the OK button The display shows pin Key in your PIN (default 0000) 7 Press the OK button You'll hear a confirmation tone from the handset and base unit. Binatone Help Line: 01325 304 473 31 E:\Binatone2003\MD1600\MD1600_03. vp 09 June 2003 15:22:12 Color profile: Generic CMYK printer profile Composite Default screen Resetting the system Reset without the PIN 1 2 Remove the batteries from the handset Press and hold the (STAR) key while you replace the batteries The display shows default Release the (STAR) key and press the OK button You'll hear a confirmation tone from the handset and base unit, and search 1 will appear on the display for a few moments. 3 32 E:\Binatone2003\MD1600\MD1600_03. vp 09 June 2003 15:22:12 Color profile: Generic CMYK printer profile Composite Default screen Multi-handset use If you have a MD 1600 Twin, Triple or Quad system, you will already have two, three or four handsets. You can also buy spare handsets and charger pods separately -- they're supplied as a Binatone MD 160 system. Altogether, you can have up to five handsets registered to the base unit, as numbers 2, 3, 4 and 5. With more than one handset registered to your base unit, you can: make intercom calls from one handset to another make a new intercom call while you are on an outside call shuttle between an outside call and an intercom call transfer an outside call from one handset to another set up a three-way conference call between yourself, an outside call and an intercom call Each handset has its own number -- 1, 2, 3, 4 or 5 -- which is shown on the right-hand side of the display. You can change the handset's name from micro to a name of your choice, as described on page 22. Please note Among the handsets registered to a single base unit, only one outside call and two intercom calls can take place at once. If you try to make an outside call while another handset is already on the line, you will hear Busy tone. If you try to make an intercom call when one is already in progress, you will hear Busy tone. When one handset has taken the outside line, the EXT symbol will appear on the displays of all other handsets. Binatone Help Line: 01325 304 473 33 E:\Binatone2003\MD1600\MD1600_03. vp 09 June 2003 15:22:12 Color profile: Generic CMYK printer profile Composite Default screen Registering new handsets ! If you have a MD 1600 Twin, Triple or Quad system, all the handsets supplied with your base unit are already registered to it -- the first one as handset number 1, the second as number 2, etc. You won't need to re-register them unless you have a problem. If you've bought extra handsets separately, you'll need to register each one to your original base unit. To register a handset 1 Press and hold the handset locator button on the base unit for about 3 seconds, until you hear two short beeps and the green IN USE light flashes You now have 3 minutes in which to register the handset. 2 Press the MENU button The display shows register (If the display does not show register at this point, press the o button until it does. ) 3 Press the OK button The display shows: These are the base station numbers. Any number that is flashing is already in use for a base station. bs 1 2 3 4 4 Key in a base unit number that is not flashing The display shows pin 34 E:\Binatone2003\MD1600\MD1600_03. vp 09 June 2003 15:22:14 Color profile: Generic CMYK printer profile Composite Default screen Registering new handsets 5 Key in your PIN (default 0000) and press the OK button The display shows search. After a few moments, when the handset finds the base unit, a number* appears on the display. 6 Press the OK button to confirm registration If the display says not sub at this point, repeat the registration procedure again from step 1. If it still doesn't work, call the Binatone Help Line for advice. [. . . ] If your PBX requires you to wait for a second Dial tone before dialling the telephone number, press the CALLER button for a pause between the access digit and the number. "My MD 1600 system won't work properly on a PBX. " You may need to change the recall setting. It will help if you have your PBX documentation to hand when you make the call. 44 E:\Binatone2003\MD1600\MD1600_03. vp 09 June 2003 15:22:16 Color profile: Generic CMYK printer profile Composite Default screen Troubleshooting If the fault persists . . . Disconnect all other instruments connected to the same line as the MD 1600 and see whether you can make a call. Disconnect the base unit from the telephone line and plug a different phone into the master telephone socket. [. . . ]