User manual LEXIBOOK SM1300

[. . . ] SET: enter to House code and Channel setting mode. °C/°F: hange between °C or °F, change channel and house code. Wall Mount Holder & Table Stand. 2 Copyright © Lexibook 2004 Copyright © Lexibook 2004 3 SM1300GB 7/8/04 5:30 PM Page 4 GETTING STARTED Battery installation remove battery cover 2 AA size batteries (SM1300) 2 AA size batteries (ASM20) Insert between terminals observing proper polarity then replace cover LOW BATTERY INDICATION: Low battery indication will be indicated (for both indoor & outdoor). Setting remote transmitters Insert batteries to start setup HOUSE CODE will flash for 8 seconds Select HOUSE CODE (1-15) by pressing °C/°F and then press SET Transmitters for each receiver must be set to the same HOUSE CODE and pressing SET CHANNEL will flash for 8 seconds Select CHANNEL(1-4) by pressing °C/°F and then press SET Humidity & Temperature will display Select °C or °F of Temperature by pressing °C/°F key * Use a different house code if your weather station detecTs other signals from neighboring sources * Factory default: house code = 01 and channel = 01 SYNCHRONIZATION SETUP Automatic Learn Function Learn function executes automatically and runs for approximately 3 minutes when batteries are first installed in the receiver. [. . . ] When the alarm is set ON, the 'on' symbol will appeart. to change the hour (in one hour 6 Copyright © Lexibook 2004 Copyright © Lexibook 2004 7 SM1300GB 7/8/04 5:30 PM Page 8 When Alarm Sounds 1 or 2 will flash Press MODE/SNOOZE to snooze the alarm for 5 minutes. Press ANY other key will shut off the alarm. Without interruption, alarm will shut off automatically after one minute. WEATHER DISPLAY Check Local Temperature (Inside) After insert batteries, local temperature will display. Check Remote Temperature & Humidity Press CHN to toggle between Channel 1, 2 and 3. Temperature and humidity readings will alternate on the receiver. °C or °F Temperature Display MOON PHASE The moon phase is automatically updated according to the year/month/day. Moon Phase Display: New Moon Young Crescent First Quarter Waxing Gibbous Full Moon Waning Gibbous Last Quarter Old Crescent Toggle between °C and °F by pressing Alarm °C/°F at Clock2 mode. Min and Max Temperature & Humidity Press Minute/-/Min in Clock1 mode to display minimum temperature and humidity. Press Hour/+/MAX in Clock1 mode to display maximum temperature and humidity. Note: Min/Max readings are automatically cleared daily at 00:00. 8 Copyright © Lexibook 2004 Copyright © Lexibook 2004 9 SM1300GB 7/8/04 5:30 PM Page 10 WEATHER DISPLAY Temperature & humidity trend The trend indicator shows the trend of temperature and humidity determined by the particular transmitter in the past half-hour interval. TEMPERATURE ALARM You can set up to 5 high temperature alarms - one local and one for each of the four remote channels. High temperature alarm Scroll to high temperature alarm mode using MODE/SNOOZE. Select channel (1, 2, 3, 4 or local) using CHN. Press + or - key to set the high temperature limit value. To disable particular alarm, press Alarm°C/°F; dashes = alarm disabled. Repeat steps to for all other channels if desired. Weather report symbols The receiver is able to monitor and display the weather status based on collected data from Channel 1. About Snow Freeze Warning * Snow symbol will flash to warn of 'snowing'. * Activated when Channel 1's temperature is between -1. 9 °C and +2. 9 °C. * Snow will appear solid if and when Channel 1's temperature falls below -1. 9 °C: it is freezing. Note: * Initially, the weather will be cloudy. * Remote transmitter Channel 1 will be used for weather indication. * If Channel 1 is empty, then weather will always be cloudy. [. . . ] Pressing any key will turn on the backlight function. To save energy, you can select to Turn Off the backlight by executing the following steps: Hold MODE/SNOOZE key to enter the clock setting mode; Press CHN key can enable /disable this feature. Ensure the remote transmitter is out of direct sunlight, and away from sources of heat. - Batteries in remote transmitter may need changing. - Move remote transmitter closer to the receiver. [. . . ]