User manual LEXMARK E350D

[. . . ] E350d and E352dn User's Guide June 2006 www. lexmark. com Lexmark and Lexmark with diamond design are trademarks of Lexmark International, Inc. , registered in the United States and/or other countries. 740 West New Circle Road Lexington, Kentucky 40550 Edition:June 2006 The following paragraph does not apply to any country where such provisions are inconsistent with local law: LEXMARK INTERNATIONAL, INC. , PROVIDES THIS PUBLICATION "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Some states do not allow disclaimer of express or implied warranties in certain transactions; therefore, this statement may not apply to you. This publication could include technical inaccuracies or typographical errors. [. . . ] Push open the latches on both ends of the memory connector. Warning: Memory is easily damaged by static electricity. Touch something metal, such as the printer frame, before you touch a memory card. Avoid touching the connection points along the edge of the card. 4 5 Align the notches on the bottom of the card with the notches on the connector. Push the memory card firmly into the connector until the latches on either end of the connector snap into place. It may require some force to fully seat the card. 6 7 8 9 10 Make sure each latch fits over the notch on each end of the card. Plug the power cord into the wall outlet and turn the printer on to continue print functions. Adding a memory card 31 Installing options Adding a flash memory card CAUTION: If you are installing a flash memory card after setting up the printer, turn the printer off, and unplug the power cord from the wall outlet before continuing. Note: Flash memory card options designed for other Lexmark printers may not work with your printer. 1 2 Access the system board (see Accessing the system board on page28 ). Note: There are two sets of holes on the system board for flash memory card installation. The flash memory card may be installed into either set of holes, however, only one flash memory card may be installed. Warning: Flash memory is easily damaged by static electricity. Touch something metal, such as the printer frame, before you touch a flash memory card. Avoid touching the metal connection points on the connector. 3 4 Squeeze the retainers, and align the plastic pins on the flash memory card with the holes on the system board. Push the flash memory card firmly into the holes of the system board until it snaps into place. 5 6 7 8 Close the side access door. Plug the power cord into the wall outlet and turn the printer on to continue print functions. Adding a flash memory card 32 Installing options Installing an optional 250-sheet drawer or 550-sheet drawer CAUTION: Turn the printer off, and unplug the power cord from the wall outlet before continuing. Place the printer unit directly on top of the 250-sheet drawer or 550-sheet drawer. Installing an optional 250-sheet drawer or 550-sheet drawer 33 Installing options Recognizing installed options The printer driver should automatically recognize the newly-installed option when the printer is turned on. If it does not, you can add the appropriate option manually. Note: If you have not installed your printer driver yet, follow the appropriate instructions on the Setup sheet supplied with your printer. After you have installed a printer driver, return here to complete these instructions. 1 2 3 4 5 Click Start à Settings à Printers. Add the appropriate options to your configuration: Memory Card--Increase the printer memory to the desired number (maximum of 160 MB). Flash Memory Card--Increase the printer flash memory to the desired number (maximum of 32 MB). 250-sheet drawer or 550-sheet drawer--Increase printing capacity by 250 to 550 sheets. 6 Click OK. Recognizing installed options 34 5 Maintaining the printer Periodically, you need to complete certain tasks to maintain optimum print quality. These tasks are covered in this chapter. If several people are using the printer, you may want to designate a key operator to do the setup and maintenance of your printer. [. . . ] You are responsible for loss of, or damage to, a product in transit to the Remarketer or the Lexmark designated location. When warranty service involves the exchange of a product or part, the item replaced becomes the property of the Remarketer or Lexmark. The replacement may be a new or repaired item. The replacement item assumes the remaining warranty period of the original product. [. . . ]