User manual LEXMARK IBM PERSONAL WHEELWRITER 2

[. . . ] This product uses a printing process that heats the print media, and the heat may cause the media to release emissions. You must understand the section in your operating instructions that discusses the guidelines for selecting print media to avoid the possibility of harmful emissions. Use care when you replace a lithium battery. Do not subject the power cord to abrasion or stress. [. . . ] Under Timeouts Screen Timeout 15­300 Timeouts Print Timeout Disabled 1­255 Sets the amount of time in seconds the printer waits before returning the printer display to a Ready state Note: 30 seconds is the factory default setting. Sets the amount of time in seconds the printer waits to receive an end-of-job message before canceling the remainder of the print job Notes: · 90 seconds is the factory default setting. · When the timer expires, any partially printed page still in the printer is printed, and then the printer checks to see if any new print jobs are waiting. · Print Timeout is available only when using PCL emulation. Timeouts Wait Timeout Disabled 15­6553515 This setting has no effect on PostScript emulation print jobs. Sets the amount of time in seconds the printer waits for additional data before canceling a print job Notes: · 40 seconds is the factory default setting. · Wait Timeout is available only when the printer is using PostScript emulation. This setting has no effect on PCL emulation print jobs. Timeouts Job Hold Timeout 5­255 Sets the amount of time the printer waits for user intervention before it holds jobs that require unavailable resources and continues to print other jobs in the print queue Notes: · 30 seconds is the factory default setting. · This menu item appears only when a hard disk is installed. Print Recovery Auto Continue Disabled 5­255 Lets the printer automatically continue printing from certain offline situations when not resolved within the specified time period Note: Disabled is the factory default setting. Understanding printer menus 112 Menu item Print Recovery Jam Recovery On Off Auto Description Specifies whether the printer reprints jammed pages Notes: · Auto is the factory default setting. The printer reprints · On sets the printer to always reprint jammed pages. · Off sets the printer to never reprint jammed pages. jammed pages unless the memory required to hold the pages is needed for other printer tasks. Print Recovery Page Protect Off On Lets the printer successfully print a page that may not have printed otherwise Notes: · Off is the factory default setting. Off prints a partial page when there is not enough memory to print the whole page. entire page prints. · On sets the printer to process the whole page so that the Factory Defaults Do Not Restore Restore Now Returns the printer settings to the factory default settings Notes: · Do Not Restore is the factory default setting. Do Not Restore keeps the user-defined settings. · Restore Now returns all printer settings to the factory default settings except Network/Ports menu settings. exiting the menus causes the printer to reset. The menu selection is updated. · Job Accounting is available only when a printer hard disk is · Changing this setting from the printer control panel and then Resource Save On Off Specifies how the printer handles temporary downloads, such as fonts and macros stored in RAM, when the printer receives a job that requires more memory than is available Notes: · Off is the factory default setting. Off sets the printer to retain · The On setting retains the downloads during language the downloads only until memory is needed. Downloads are deleted in order to process print jobs. If the printer runs out of memory, 38 Memory Full appears, and downloads are not deleted. Print All Order Alphabetical Oldest First Newest First Specifies the order in which held and confidential jobs are printed when Print All is selected Notes: · Alphabetical is the factory default setting. · Print jobs always appear in alphabetical order on the printer control panel. Understanding printer menus 115 Finishing menu Menu item Sides (Duplex) 1 sided 2 sided Description Specifies whether duplex (2-sided) printing is set as the default for all print jobs Notes: · 1 sided is the factory default setting. · To set 2-sided printing from the software program: for Windows users, click File ª Print, and then click Properties, Preferences, Options, or Setup; for Macintosh users, choose File > Print, and then adjust the settings from the print dialog and pop-up menus. Duplex Binding Long Edge Short Edge Defines the way duplexed pages are bound and how the printing on the back of the page is oriented in relation to the printing on the front of the page Notes: · Long Edge is the factory default setting. · Long Edge specifies that binding be placed on the left edge of portrait pages and the top edge of landscape pages. and the left edge of landscape pages. · Short Edge specifies that binding be placed on the top edge of portrait pages Copies 1­999 Blank Pages Do Not Print Print Collate Off (1, 1, 1, 2, 2, 2) On (1, 2, 1, 2, 1, 2) Specifies a default number of copies for each print job Note: 1 is the factory default setting. Specifies whether blank pages are inserted in a print job Note: Do Not Print is the factory default setting. Stacks the pages of a print job in sequence when printing multiple copies Notes: · Off is the factory default setting. [. . . ] Lexmark may terminate your license upon notice if you fail to comply with any of the terms of this License Agreement. Upon such termination, you agree to destroy all copies of the Software Program together with all modifications, documentation, and merged portions in any form. services and personal property taxes, resulting from this Agreement or your Use of the Software Program. party more than two years after the cause of action has arisen, except as provided under applicable law. 11 TAXES. [. . . ]