User manual LEXMARK X644E

[. . . ] X644e, X646e User's Guide January 2006 www. lexmark. com Lexmark and Lexmark with diamond design are trademarks of Lexmark International, Inc. , registered in the United States and/or other countries. 740 West New Circle Road Lexington, Kentucky 40550 Edition: January 2006 The following paragraph does not apply to any country where such provisions are inconsistent with local law: LEXMARK INTERNATIONAL, INC. , PROVIDES THIS PUBLICATION "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Some states do not allow disclaimer of express or implied warranties in certain transactions; therefore, this statement may not apply to you. This publication could include technical inaccuracies or typographical errors. [. . . ] See Setting the Paper Type and Paper Size for help. From the computer software application, set the paper type, size, and source according to the media you loaded. Windows a b c From a word processor, spreadsheet, browser, or other application, select File Print. Click Properties (or Options, Printer, or Setup, depending on the application) to view the MFP driver settings. A paper tray list will appear. d Select the tray containing the specialty media. Note: If you have difficulty, click Help, and then follow the driver instructions. e f g Mac OS 9 a b c d e Mac OS X a b c d e f g h i Select the media type (transparencies, envelopes, and so on) from the Paper Type list box. Select the size of the specialty media from the Paper Size list box. Click OK, and then send the print job as usual. Select File Page Setup. Select the size of the specialty media from the Paper pop-up menu, and then click OK. Select File Print. With General selected on the top pop-up menu, go to the Paper Source pop-up menu, and select the tray containing the specialty media or the name of the media. Click Print. Select File Page Setup. Select the MFP from the Format for pop-up menu. Select the size of the specialty media from the Paper pop-up menu, and then click OK. Select File Print. On the Copies & Pages pop-up menu, select Imaging. Select the specialty media on the Paper Type pop-up menu. On the Imaging pop-up menu, select Paper Feed. Select the tray containing the specialty media from the All pages from or First page from / Remaining from pop-up menus. Click Print. Printing on specialty media 61 Printing Loading standard trays and optional trays The MFP has a 500-sheet standard tray. You may have also purchased one or more 250-sheet or 500-sheet optional trays or a 2000-sheet drawer. The steps for loading a 250-sheet tray or 500-sheet tray are the same. Note: The steps for loading a 2000-sheet drawer are different than the steps for loading a 250-sheet tray or 500-sheet tray. To load print media: Note: Do not remove a tray when a job is printing or when the control panel green indicator light is blinking. Doing so may cause a jam. 1 2 Remove the tray from the MFP, and place it on a flat, level surface. Squeeze the side guide tab, and slide the guide to the outer edge of the tray. 3 4 Squeeze the rear guide tab, and slide the guide to the correct position for the size media you are loading. Flex the sheets back and forth to loosen them, then fan them. Straighten the edges on a level surface. Size indicators Loading standard trays and optional trays 62 Printing 5 Place the print media in the tray: Note: Paper must be loaded differently in the trays, depending on the options you have installed. [. . . ] This equipment uses CA11A telephone jacks. Notices 140 Notices Notice to users of the New Zealand telephone network The following are special conditions for the Facsimile User Instructions. The grant of a telepermit for any item of terminal equipment indicates only that Telecom has accepted that the item complies with minimum conditions for connection to its network. It indicates no endorsement of the product by Telecom, nor does it provide any sort of warranty. Above all, it provides no assurance that any item will work correctly in all respects with another item of telepermitted equipment of a different make or model, nor does it imply that any product is compatible with all of Telecom's network services. [. . . ]