User manual LG 71PY1MC

[. . . ] PLASMA MONITOR MODELS: 71PY1M 71PY1MG 71PY1MC 71PY1MV OWNER'S MANUAL Please read this manual carefully before operating your set. Record model number and serial number of the set. See the label attached on the back cover and quote this information to your dealer when you require service. Safety Instructions Safety Instructions WARNING Do not place the set in direct sunlight or near heat sources such as heat registers, stove and so on. - This may cause a fire. Do not use the set in damp place such as a bathroom or any place where it is likely to get wet. - This may cause a fire or could give an electric shock. Bend antenna cable between inside and outside building to prevent rain from flowing in. - This may cause water damaged inside the set and could give an electric shock. Earth wire should be connected. - If the earth wire is not connected, there is possible a danger of electric shock caused by the current leakage. - If grounding methods are not possible, a separate circuit breaker should be employed and installed by a qualified electrician. [. . . ] When the number of minutes you want is displayed on the screen, press the ENTER button. The timer begins to count down from the number of minutes selected. To check the remaining minutes before the monitor turns off, press the SLEEP or ENTER button once. To cancel the Sleep Timer, press the SLEEP button repeatedly until zz zz --- Min appears. Owner's Manual 25 Operation Special Menu Options Key Lock - The monitor can be set up so that it can only be used with the remote control. - This feature can be used to prevent unauthorized viewing by disabling the front panel controls. - This Monitor is programmed to remember which option it was last set to even if you turn the monitor off. PICTURE SOUND TIMER SPECIAL SCREEN PIP/DW Language Key lock ISM Method Low power Set ID Index SCREEN PIP/DW PICTURE SOUND TIMER SPECIAL Language Key lock ISM Method Low power Set ID Index G On Off Move Select Move Select 1. Press the G D /E button to select the SPECIAL menu. button and then use D /E button to select Key lock. 3. Press the G button and then use D /E button to select On or Off. W Key lock' · When you select On, the display ` appears on the screen if any button on the front panel is pressed. 4. Press the ENTER button to save the new settings. -In setting Key lock `On', if the monitor is turned off with the remote control, press the INPUT on the monitor or POWER, INPUT on the remote control to turn the monitor on. ISM (Image Sticking Minimization) Method - A frozen still picture from a PC/video game displayed on the screen for prolonged periods will result in an ghost image remaining; even when you change the image. Avoid allowing a fixed or still image to remain on the Monitor's screen for a long period of time. PICTURE SOUND TIMER SPECIAL SCREEN PIP/DW Language Key lock ISM Method Low power Set ID Index SCREEN PIP/DW PICTURE SOUND TIMER SPECIAL Language Key lock ISM Method Low power Set ID Index G Normal White wash Orbiter Inversion Move Select Move Select 1. Press the G G D /E button to select the SPECIAL menu. button and then use button and then use D /E D /E button to select ISM Method. button to select either Normal, White wash, Orbiter, or Inversion. · Normal If image sticking is never a problem, ISM is not necessary - set this to Normal. · White wash White Wash removes permanent images from the screen. Note: An excessive permanent image may be impossible to clear completely using White Wash. To return to normal viewing, press the any button. · Orbiter Orbiter may help prevent ghost images. However, it is best not to allow any fixed image to remain on the screen. To avoid a permanent image on the screen, the image will move every 2 minutes. · Inversion Inversion will automatically invert the plasma display panel color every 30 minutes. Press the ENTER button to save the new settings. 26 Plasma Monitor Operation ENGLISH Low Power - Low power reduces the plasma display's power consumption. PICTURE SOUND TIMER SPECIAL SCREEN PIP/DW Language Key lock ISM Method Low power Set ID Index PICTURE SOUND TIMER SPECIAL SCREEN PIP/DW Language Key lock ISM Method Low power Set ID Index G On Off Move Select Move Select 1. [. . . ] ISM Method (Command2:p) G To avoid having a fixed image remain on screen. Transmission [j][p][ ][Set ID][ ][Data][Cr] Data 0: Normal 1: White wash Acknowledgement [p][ ][Set ID][ ][OK][Data][x] Data 0: Normal 1: White wash 40 Plasma Monitor 2: Orbiter 3: Inversion 2: Orbiter 3: Inversion [m][c][ ][Set ID][ ][Data][Cr] Data Key code : Refer to See page 42. Acknowledgement [c][ ][Set ID][ ][OK][Data][x] IR Code IR Code How to Connect G Connect your wired remote control to the Remote Control port on the Monitor. ENGLISH Remote Control IR Code G Output waveform Single pulse, modulated with 37. 917KHz signal at 455KHz TC Carrier frequency FCAR = 1/TC = fOSC/12 Duty ratio = T1/TC = 1/3 T1 G Configuration of frame · 1st frame Lead code Low custom code High custom code Data code Data code C0 C1 C2 C3 C4 C5 C6 C7 C0 C1 C2 C3 C4 C5 C6 C7 D0 D1 D2 D3 D4 D5 D6 D7 D0 D1 D2 D3 D4 D5 D6 D7 · Repeat frame Repeat code Tf G Lead code 9 ms 4. 5 ms G Repeat code 0. 55 ms 9 ms 2. 25 ms G Bit description · Bit "0" 0. 56 ms · Bit "1" 0. 56 ms 1. 12 ms G Frame interval : Tf The waveform is transmitted as long as a key is depressed. Tf Tf 2. 24 ms Tf=108ms @455KHz Owner's Manual 41 IR Code Code (Hexa) 10 11 12 13 14 15 16 17 18 19 0E 09 08 02 03 00 01 4D 52 44 0B 43 79 62 64 07 06 40 41 5B 60 92 61 6B CD CE 3E 75 99 5A D0 BF D4 D5 C6 Function Number Key 0 Number Key 1 Number Key 2 Number Key 3 Number Key 4 Number Key 5 Number Key 6 Number Key 7 Number Key 8 Number Key 9 SLEEP MUTE POWER VOL+ VOLCH+ CHAPC DASP ENTER (Á) AII INPUT SELECT MENU ARC Window Position Window Size F G D E Note R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button (Power On/Off) R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button (4:3/16:9/Horizon/Zoom mode Selection) R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button Discrete IR Code (Only RGB mode) Discrete IR Code (Input Video 1 Selection) Discrete IR Code (Input Video 2 Selection) Discrete IR Code (Input Component 1 Selection) Discrete IR Code (Input Component 2 Selection) Discrete IR Code (Input RGB Selection) Discrete IR Code (Input HDMI1/DVI Selection) EXIT PIP XD PIP Input DW Video HDMI2 Key lock Index Auto config. [. . . ]