User manual LG A09AHD

[. . . ] WIRING DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SPECIFICATIONS OF ELECTRICAL PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . REFRIGERANT CYCLE DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . CONTROL BLOCK DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Open the air inlet grille upward and pull it toward you. Remove the terminal cover and cord clamp. Insert the connecting cable (according to the local cords) into the pipe hole on the wall. Take out the connecting cable through the cable slot on the rear panel so that it protrudes about 15 cm from the front. Insert the connecting cable fully into the terminal block and secure it tightly with screws. Tightening torque :1. 2 N·m (0. 12 kgf·m) 7. Secure the connecting cable with the cord clamp. Fix the terminal cover, rear plate bushing and air inlet grille on the indoor unit. 1. Die-cutting Front panel slit Cut out the slit on the left or right side of the front panel for the left or right connection and the slit on the bottom left or right side of the front panel for the bottom left or right connection with a pair of nippers. 2. Changing drain hose For left connection, left-bottom connection and rear-left connection's piping, it is necessary to change the drain hose and drain cap. How to remove the Drain Cap Clip drain cap by needle-nose plier, and pull out. CAUTION · Be sure to refer to the wiring system diagram labeled inside the front panel. · Check local electrical cords and also any specific wiring instructions or limitations. Terminal cover Screw Cord clamp Teminal block How to install the Drain Hose Firmly insert drain hose connecting part until hitting on a heat insulator. Heat insulator How to fix the Drains Cap Screw Earth wire 4 mm 1) Insert hexagonal wrench (4 mm) in a center head. Connecting cable Screw NOTE · Wire type : More than H07RN-F or 245IEC66 (1. 0 mm2 or more) 80 mm 10mm 10mm 2) Firmly insert drains cap. No gap Do not apply lubricating oil (refrigerant machine oil) when inserting the drain cap. In case of leftward piping and rear-leftward piping, bind the auxiliary pipes (two) only with facing tape. Indoor unit Auxiliary pipes Connecting cable Installation plate Drain hose Inside the room Extension drain hose Fig. 9-2-13 Arrange the drain pipe for proper drainage from the unit. Improper drainage can result in dew-dropping. This air conditioner has the structure designed to drain water collected from dew, which forms on the back of the indoor unit, to the drain pan. Therefore, do not store the power cord and other parts at a height above the drain guide. Space for pipes Wall Drain guide · Carefully arrange pipes so that any pipe does not stick out of the rear plate of the indoor unit. · Carefully connect the auxiliary pipes and connecting pipes to each other and cut off the insulating tape wound on the connecting pipe to avoid double-taping at the joint, moreover, seal the joint with the vinyl tape, etc. · Since dewing results in a machine trouble, make sure to insulate both the connecting pipes. (Use polyethylene foam as insulating material. ) · When bending a pipe, carefully do it not to crush it. Fig. Setting of Remote Controller Selector Switch When two indoor units are installed in the separated rooms, there is no need to change the select switches. (1) Stop the operation of the air conditioner and turn turn off its main power supply. (2) Pull the air inlet grille toward you to open it and remove the air inlet grille. [. . . ] MCC-867 (RAS-M13UKV-E) P Board Ass'y, . C. MCC-867 (RAS-M16UKV-E) P Board Ass'y, . C. MCC-867 (RAS-M10UKCV-E) P Board Ass'y, . C. MCC-867 (RAS-M13UKCV-E) P Board Ass'y, . C. [. . . ]