User manual LG AG S230

[. . . ] When watching 3D video, ensure that you are viewing the video within the specified receiving range. (For more information, please refer to the user manual of the TV or the PROJECTOR. ) If the receiving range is out of the specified range, the screen may not be viewable as 3D video. Flickering may be generated by the 3D glasses (60 Hz) when watching the 3D screen when a magnetic fluorescent lamp (50 Hz) is on. If you encounter this symptom, please turn off the light and continue watching. [. . . ] You can enjoy movies or pictures made as 3D. ACCESSORIES ENGLISH *1 *2 3D Glasses 8-pin mini USB cable Manual CD Quick Start Guide Pouches !NOTE The accessories represented in this manual may differ from the actual appearances. PART NAMES AG-S230 (For Children) Nose Pad 3D Glasses' Lenses Power Button LED indicator 3D Glasses' Lenses AG-S250 (For Audlts) Nose Pad Power Button LED indicator AG-S270 (Made of Metal) Nose Pad 3D Glasses' Lenses Power Button LED indicator USB port (charging port) 8-pin mini USB cable USB port (charging port) 8-pin mini USB cable USB port (charging port) 8-pin mini USB cable USING 3D GLASSES Button Operation Power On Power Off Auto Off*1 Battery (Lithium polymer) discharge How to connect the glasses How to 2 re-connect the glasses* Press the Power button once. LED Indication The red LED blinks once. Press and hold down the Power button (2 second The red LED blinks three times. ~3 second) The device is automatically switched off if there is The red LED blinks three times. If the battery is discharged, the LED blinks for 1 minute and turns off automatically. * When charging is completed, the LED is lit green. When initially switched on, the device will a u to m a t i c a l l y b e c o n n e c te d to t h e T V o r PROJECTOR with the strongest signal. Release the button when the green LED light turns on. Then, you will see the green light blink three times before the device is switched off. If you switch the power on again, the glasses will be connected to the TV or PROJECTOR with the strongest signal. - - Press the power button for over eight seconds. The Auto Off function automatically switches the power off when the glasses lose signal from the TV or the PROJECTOR. This may occur when the distance or angle between the device and the TV or PROJECTOR are out of range; when there is a barrier between the two devices; or when the device is switched from 3D to 2D mode. The device recognizes the unique ID of the TV or PROJECTOR to which it is connected. Thus, IDs of other TVs or PROJECTORs are not recognized by the device. If you wish to re-connect the device to other TVs or PROJECTORs, please see "How to re-connect the glasses". (see how to use the 3D glasses) You can view 3D images with the device even while recharging it with a USB cable. During recharge, the LED light of the device indicates: When the device is on and there are 3D images: When the device is off or on and there are no 3D images The red light blinks every second during recharge and the green light blinks every second when fully recharged. Either the red or the green light stays on depending on the recharge status. 3 CHARGING THE GLASSES 1 Connect the USB port located under the power button on the glasses to the USB port of the TV or PC using the supplied 8-pin mini USB cable as shown by the figure. CAUTION Do not insert the supplied 8-pin mini USB cable in the reverse direction. Otherwise, this may cause damage to the product. ENGLISH i. e) AG-S250 2 Charge the glasses until the LED is green. The glasses will fully charge in about 1 hours 50 minute. !NOTE While charging: The LED is red. When charging is complete: The LED is green. When the battery is discharged: The LED blinks for 1 minute and turns off automatically. CAUTION If you use a USB cable other the one (8-pin mini USB) supplied with the product, the product may be damaged. This equipment shall be powered with USB 2. 0 or higher. HOW TO WEAR THE 3D GLASSES Using 3D glasses may cause minor inconveniences. [. . . ] This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: · Reorient or relocate the receiving antenna. · Increase the separation between the equipment and receiver. [. . . ]