User manual LG DC460E

[. . . ] The route of the flue must be as short as possible. Do not connect the extractor hood to exhaust ducts carrying combustion fumes (boilers, fireplaces, etc. ). If the extractor is used in conjunction with non-electrical appliances (e. g. gas burning appliances), a sufficient degree of aeration must be guaranteed in the room in order to prevent the backflow of exhaust gas. [. . . ] · Repeat this operation on the other side. · Drill ø 8 mm holes at all the centre points marked. · Insert the wall plugs 11 in the holes. · Fix the lower bracket 7. 2. 1 using the 12a screws (4, 2 x 44, 4) supplied. · Fix the upper bracket 7. 2. 1 and the air outlet connection support 7. 3 together using the 2 screws 12a (4, 2 x 44, 4) supplied. · Insert the two screws 12a (4, 2 x 44, 4) supplied in the hood body fixing holes, leaving a gap of 5-6 mm between the wall and the head of the screw. X 7. 2. 1 EN 1 18 8 Mounting the hood body · Before attaching the hood body, tighten the two screws Vr located on the hood body mounting points. · Hook the hood body onto the screws 12a. · Fully tighten support screws 12a. · Adjust screws Vr to level the hood body. Vr 12a Connections DUCTED VERSION AIR EXHAUST SYSTEM When installing the ducted version, connect the hood to the chimney using either a flexible or rigid pipe ø 150 or 120mm, the choice of which is left to the installer. To install a ø 150 · To install the dumper 10 · Fix the pipe in position using sufficient pipe clamps (not supplied). To install a ø 120 · To install a ø 120 mm air exhaust connection, insert the reducer flange 9 on the dumper 10. · Fix the pipe in position using sufficient pipe clamps (not supplied). · Remove any activated charcoal filters. 14. 1 ø 150 10 9 10 ø 120 RECIRCULATION VERSION AIR OUTLET · Put connection 15 into the connection support 7. 3. · Insert the connection extension pieces laterally 14. 1 in connection 15. · Make sure that the outlet of the extension pieces 14. 1 is horizontally and vertically aligned with the chimney outlets. · Connect the air outlet connection 15 to the hood body outlet using either a flexible or rigid pipe ø 150 mm, the choice of which is left to the installer. · Ensure that the activated charcoal filters have been inserted. 15 ø 150 EN 1 19 9 ELECTRICAL CONNECTION · Connect the hood to the mains through a two-pole switch having a contact gap of at least 3 mm. · Remove the grease filters (see paragraph Maintenance) being sure that the connector of the feeding cable is correctly inserted in the socket placed on the side of the fan. 7. 2. 1 Flue assembly 12c Upper exhaust flue · Slightly widen the two sides of the upper flue and hook them behind the brackets 7. 2. 1, making sure that they are well seated. · Secure the sides to the brackets using the 4 screws 12c (2, 9 x 9, 5) supplied. · Make sure that the outlet of the extensions pieces is aligned with the chimney outlets. [. . . ] Als het symbool met de doorgekruiste verrijdbare afvalbak op een product staat, betekent dit dat het product valt onder de Europese Richtlijn 2002/96/EC. Elektrische en elektronische producten mogen niet worden meegegeven met het huishoudelijk afval, maar moeten worden ingeleverd bij speciale inzamelingspunten die door de lokale of landelijke overheid zijn aangewezen. De correcte verwijdering van uw oude toestel helpt negatieve gevolgen voor het milieu en de menselijke gezondheid voorkomen. Wilt u meer informatie over de verwijdering van uw oude toestel? [. . . ]