User manual LG E1911T

[. . . ] ENGLISH OWNER'S MANUAL LCD MONITOR Please read this manual carefully before operating your set and retain it for future reference. LCD MONITOR MODEL E1911T E1911S E2211T E2211S E2411T www. lg. com Important Precautions This unit has been engineered and manufactured to ensure your personal safety, however improper use may result in potential electrical shock or fire hazards. In order to allow the proper operation of all safeguards incorporated in this display, observe the following basic rules for its installation, use, and servicing. On Safety Use only the power cord supplied with the unit. In case you use another power cord, make sure that it is certified by the applicable national standards if not being provided by the supplier. If the power cable is faulty in any way, please contact the manufacturer or the nearest authorized repair service provider for a replacement. [. . . ] Do not carry the product upside down holding only the stand base. The product may fall and get damaged or injure your foot. 5 Connecting the Display Disassembling the stand 1. Put a cushion or soft cloth on aflat surface. 2. Place the monitor face Down on the cushion or soft cloth. 3. Change your lock on the product as it follows and turn it in the arrow direction. . If you can't release the stand base even the locking knob is at a release position, Please push the indicated knob down and retry it. 6 Connecting the Display 4. Pushing the PUSH button, Take the stand body from hinge body. Good Position Bad Position Warning: You can hurt your finger. 7 Connecting the Display Before setting up the monitor, ensure that the power to the monitor, the computer system, and other attached devices is turned off. Positioning your display -After installation, adjust the angle as shown below. 1. Adjust the position of the panel in various ways for maximum comfort. Tilt Range : -5° to 15° Do not touch or press the screen when adjusting the angle of the monitor. When adjusting the angle of the screen, do not put your finger(s) in between the head of the monitor and the stand body. You can hurt your finger(s). ERGONOMIC It is recommended that in order to maintain an ergonomic and comfortable viewing position, the forward tilt angle of the monitor should not exceed 5 degrees. 8 Connecting the Display Connecting with the PC E1911T/E2211T/E2411T 1. Before setting up the monitor, ensure that the power to the monitor, the computer 2. Connect signal input cable 1 system, and other attached devices is turned off. A Connect DVI-D(Digital signal) Cable B Connect D-sub(Analog signal) Cable 2 in order, then tighten the screw NOTE This is a simplified representation of the rear view. This rear view represents a general model; your display may differ from the view as shown. When using a D-Sub signal input cable connector for Macintosh Mac adapter : For Apple Macintosh use, a separate plug adapter is needed to change the 15 pin high density (3 row) D-sub VGA connector on the supplied cable to a 15 pin 2 row connector. Varies according to model. Connect the signal input cable and tighten it up by turning in the direction of the arrow as shown in the figure. Wall-outlet type DVI-D (This feature is not available in all countries. ) 3. Press the power button on the front panel to turn the power on. When monitor power is turned on, the 'Self Image Setting Function' is executed automatically. (Only Analog Mode) Power Button NOTE ` Self Image Setting Function'?This function provides the user with optimal display settings. When the user connects the monitor for the first time, this function automatically adjusts the display to optimal settings for individual input signals. When you encounter problems such as blurry screen, blurred letters, screen flicker or tilted screen while using the device or after changing screen resolution, press the AUTO function button to improve resolution. 9 Connecting the Display Connecting with the PC E1911S/E2211S 1. Before setting up the monitor, ensure that the power to the monitor, the computer 2. Connect signal input cable 1 system, and other attached devices is turned off. and power cord of the signal cable. A Connect D-sub(Analog signal) Cable 2 in order, then tighten the screw NOTE This is a simplified representation of the rear view. This rear view represents a general model; your display may differ from the view as shown. When using a D-Sub signal input cable connector for Macintosh Mac adapter : For Apple Macintosh use, a separate plug adapter is needed to change the 15 pin high density (3 row) D-sub VGA connector on the supplied cable to a 15 pin 2 row connector. Varies according to model. Connect the signal input cable and tighten it up by turning in the direction of the arrow as shown in the figure. Wall-outlet type 3. [. . . ] Digital E1911T Sync Input Video Input Signal Input Input Form 15 pin D-Sub Connector DVI-D Connector (Digital) RGB Analog (0. 7 Vp-p/ 75 ohm), Digital VESA 1366 x 768 @ 60 Hz VESA 1366 x 768 @ 60 Hz Resolution Plug&Play Power Consumption Dimensions & Weight Max Recommend DDC 2B(Digital), DDC 2AB(Analog) On Mode Sleep Mode Off Mode : < < 18 W(Typ. ) 0. 3 W 0. 3 W Without Stand Width 44. 2 cm ( 17. 42 inch ) Height 26. 7 cm ( 10. 51 inch ) Depth 6. 1 cm ( 2. 40 inch ) 2. 8 kg ( 6. 19 lb ) With Stand Width 44. 2 cm ( 17. 42 inch ) Height 35. 8 cm ( 14. 09 inch ) Depth 17. 0 cm ( 6. 69 inch ) Weight(excl. packing) Range Power Input Environment al Conditions Tilt : -5° to 15° AC 100-240 V~ 50 / 60 Hz 0. 8 A Operating Conditions Temperature 10 °C to 35 °C Humidity 10 % to 80 % non-Condensing Storage Conditions Temperature -20 °C to 60 °C Humidity 5 % to 90 % non-Condensing Stand Base Power cord Attached ( ), Detached ( O ) Wall-outlet type NOTE Information in this document is subject to change without notice. 25 Specifications Display 47. 0 cm (18. 5 inch) Flat Panel Active matrix-TFT LCD Anti-Glare coating Visible diagonal size : 47. 0 cm 0. 300 mm x 0. 300 mm (Pixel pitch) Horizontal Freq. Input Form Signal Input Input Form Max Recommend DDC 2AB On Mode Sleep Mode Off Mode : < < 18 W(Typ. ) 0. 3 W 0. 3 W Without Stand Width 44. 2 cm ( 17. 42 inch ) Height 26. 7 cm ( 10. 51 inch ) Depth 6. 1 cm ( 2. 40 inch ) 2. 8 kg ( 6. 19 lb ) 30 kHz to 61 kHz (Automatic) 56 Hz to 75 Hz (Automatic) Separate Sync. 15 pin D-Sub Connector RGB Analog (0. 7 Vp-p/ 75 ohm) VESA 1366 x 768 @ 60 Hz VESA 1366 x 768 @ 60 Hz E1911S Sync Input Video Input Resolution Plug&Play Power Consumption Dimensions & Weight With Stand Width 44. 2 cm ( 17. 42 inch ) Height 35. 8 cm ( 14. 09 inch ) Depth 17. 0 cm ( 6. 69 inch ) Weight(excl. [. . . ]