User manual LG E2350V

[. . . ] User's Guide E2250V E2350V Make sure to read the Important Precautions before using the product. Keep the User's Guide(CD) in an accessible place for future reference. See the label attached on the product and give the information to your dealer when you ask for service. Important Precautions This unit has been engineered and manufactured to ensure your personal safety, however improper use may result in potential electrical shock or fire hazards. In order to allow the proper operation of all safeguards incorporated in this display, observe the following basic rules for its installation, use, and servicing. On Safety Use only the power cord supplied with the unit. In case you use another power cord, make sure that it is certified by the applicable national standards if not being provided by the supplier. [. . . ] Press the button as shown, and pull the stand body up. Pr es s 3. After pull the stand body up, take the monitor up carefully and face the front side. (Once you pull the stand body up, please keep pressing the button. If you don't press the button, it will damage the product. ) When limited tilt degree, the button is not working, pull stand body up or down a little. 6 Connecting the Display 4. If you want to use the stand base, pull the stand body down. (Once you pull the stand body down, please keep pressing the button. If you don't press the button, it will damage the product. ) 5. Use a coin on the back of the stand base and turn the screw clockwise to tighten. 6. Once assembled take the monitor up carefully and face the front side. Important This illustration depicts the general model of connection. Your monitor may differ from the items shown in the picture. Do not carry the product upside down holding only the stand base. The product may fall and get damaged or injure your foot. 7 Connecting the Display Before setting up the monitor, ensure that the power to the monitor, the computer system, and other attached devices is turned off. Positioning your display After installation, adjust the angle as shown below. * With stand base Adjust the position of the panel in various ways for maximum comfort. Tilt Range : -5° to 15° Do not touch or press the screen when adjusting the angle of the monitor. When adjusting the angle of the screen, do not put your finger(s) in between the head of the monitor and the stand body. You can hurt your finger(s). ERGONOMIC It is recommended that in order to maintain an ergonomic and comfortable viewing position, the forward tilt angle of the monitor should not exceed 5 degrees. 8 Connecting the Display Before setting up the monitor, ensure that the power to the monitor, the computer system, and other attached devices is turned off. Positioning your display * Without stand base Ergonomic It is recommended that in order to maintain an ergonomic and comfortable viewing position, the backward tilt angle of the monitor should exceed 10 degrees. 9 Connecting the Display Connecting with the PC 1. Before setting up the monitor, ensure that the power to the monitor, the computer 2. Connect signal input cable 1 system, and other attached devices is turned off. A Connect DVI-D(Digital signal) Cable B Connect D-sub(Analog signal) Cable C Connect HDMI Cable 2 in order, then tighten the screw AV equipment (Set-Top Box, DVD, Video, Video Game Console) Varies according to model. * HDMI is optimized on the AV equipment. * Not supported PC Headphone/Earphone Input DVI-D (This feature is not available in all countries. ) Wall-outlet type OR When using a D-Sub signal input cable connector for Macintosh Wall-outlet type Mac adapter : For Apple Macintosh use, a separate plug adapter is needed to change the 15 pin high density (3 row) D-sub VGA connector on the supplied cable to a 15 pin 2 row connector. NOTE This is a simplified representation of the rear view. This rear view represents a general model; your display may differ from the view as shown. 10 Connecting the Display Connecting with the PC 3. Press the power button on the front panel to turn the power on. When monitor power is turned on, the 'Self Image Setting Function' is executed automatically. (Only Analog Mode) Power Button NOTE ` Self Image Setting Function'?This function provides the user with optimal display settings. When the user connects the monitor for the first time, this function automatically adjusts the display to optimal settings for individual input signals. When you encounter problems such as blurry screen, blurred letters, screen flicker or tilted screen while using the device or after changing screen resolution, press the AUTO function button to improve resolution. 11 Control Panel Functions Front Panel Controls MENU Button OSD LOCKED/UNLOCKED This function allows you to lock the current control settings, so that they cannot be inadvertently changed. Press and hold the MENU button for several seconds. [. . . ] Set the color setting higher than 24 bits (true color). G Any horizontal noise appearing in any image or characters are not clearly portrayed. IMPORTANT Check Control Panel --> Display --> Settings and see if the frequency or the resolution were changed. If yes, readjust the video card to the recommend resolution. If the recommended resolution (optimal resolution) is not selected, letters may be blurred and the screen may be dimmed, truncated or biased. Make sure to select the recommend resolution. [. . . ]