User manual LG F-1068LD

[. . . ] Adjusting the Air Flow Direction Vertically . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Selecting Energy Saving Mode (Only F3/A3/G3 models) . . . . . . . . . . 5 6 6 7 7 8 RECOMMENDATIONS FOR USE Operating Recommendation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Temperature and Humidity Ranges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Cleaning Your Air Conditioner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Power plug The type of the power plug may differ according to the type of local power supply. Power cable Power cable connection should be committed to Blue Brown Yellow/Green an installation engineer. Main Power Earth F0/A0/G0 Operating mode selection dial Temperature control dial F1/A1/G1 Operating mode selection dial Temperature control dial Air flow blade swing switch F3/A3/G3 Operating mode selection dial Air flow blade swing switch Temperature control dial Energy Saver switch E-4 Cooling Your Room ENGLISH You must select the Cool mode if you wish to lower the temperature in your room. You can also set the fan speed. 1 Select the operating mode and fan speed. Set the operating mode selection dial to. . . High fan speed Between HIGH and LOW Low fan speed Result: HI COOL MED COOL LOW COOL 2 The air conditioner starts up in Cool mode. The fan starts up at the speed selected. You can change modes at any time. To adjust the temperature, turn the temperature control dial to the desired position. Possible temperatures: Between 18°C and 29°C inclusive. Result: The air conditioner starts cooling if the room temperature is higher than the selected temperature. 29°C ~ 27°C 27°C ~ 23°C 23°C ~ 18°C 3 To control the direction of the air flow, refer to page 7. E-5 Airing Your Room If the atmosphere in your room is stale, you can air it using the Fan feature and if necessary, evacuate the stale air outside. 1 If you wish to evacuate stale air outside, push the ventilation lever on the front of the unit to the right and the open position ( ). Result: The air inside the room circulates and stale air is evacuated outside. ). Otherwise, push the ventilation lever to the left and the closed position ( Result: The air simply circulates inside the room. 2 Set the operating mode selection dial to the HI FAN or LOW FAN position. HI FAN : The fan turns rapidly. 2 Remove the safety clip and the front grille. 3 When reassembling the front grille, you should install the safety clip again. Safety clip 2 Pull the air filter to the right side. 3 Remove all dust on the air filter with a vacuum cleaner or brush. 4 When you have finished, insert the air filter back into its original position. 5 Wipe the surface of the unit with a neutral detergent and then wipe it again with dry cloth. (Be sure not to use benzene, solvent or other chemical products. ) If you. . . Will not be using the air conditioner for a long period of time Then. . . Set the operating mode selection dial to "LOW FAN" and let it run of a few hours to dry the inside of the air conditioner thoroughly. Switch the air conditioner off and unplug it from the wall socket. Set the operating mode selection dial to "LOW FAN" and let it run of a few hours to dry the inside of the air conditioner thoroughly. Have not used the air conditioner for a long period of time Cleaning Your Air Conditioner (A0/A1/A3/G0/G1/G3 models) To get the best possible use out of your air conditioner, you must clean it regularly by two weeks to remove the dust on the air filter. Before cleaning your air conditioner, ensure that it is switched off and unplugged from the wall socket. 1 Open the front grille by pulling on the tabs of the unit. The removal of the front grille makes it easier to clean the air conditioner. After opening the front grille, lift it up as much as possible, then pull down to release it. 2 Front grille Grasp the handle on the air filter and lift it slightly and then out to the front. 3 Remove all dust on the air filter with a vacuum cleaner or brush. 4 When you have finished, slide the air filter back into position. Front grille 5 Clean the outer surfaces with a damp cloth and mild detergent (do NOT use benzene, solvents or other chemicals). Wipe them dry with a clean, soft cloth. Grille groove Body guide If you. . . Will not be using the air conditioner for a long period of time Then. . . Set the fan going for a few hours to dry the inside of the air conditioner thoroughly. Switch the air conditioner off and unplug it from the wall socket. Aluminum house wiring may pose special problems consult a qualified electrician. This unit requires a separate circuit, serving only this appliance. E-13 Installation Before installation, be sure to check the installation area for the air conditioner, and drain hose. [. . . ] 3 When installing the air conditioner, be sure to obtain sufficient space on the rear side of the unit for smooth flow of air. When operating the air conditioner in closed areas such as inner building with cooling operation, and result in trouble with the unit. The appliance must be fixed well by screw or similar method. Awning 75mm min. 300mm "A" 500mm 500mm 500mm Fence, wall or other obstacle Approx. 3° Model N D M "A" 180mm 220mm 240mm 750mm 150mm min. If the wall is greater than 150mm thick, cut the wall back on a 45° angle if possible. Outdoor Side 45° 45° Indoor Side 100mm or more E-14 Installation of the Drain Tube Fix the drain tube as shown in the figure. Rear Rubber cap Gasket Drain Tube Screws(2EA) Installation of the Drain Pan The procedure for installing the drain pan should be determined by the condition of the installing area. In the case of an area where the drain pan can not be directly installed on the rear side of the unit after installing the air conditioner. [. . . ]