User manual LG GR-B4090-BVQW

[. . . ] Notational Failure to follow directions noted by this symbol could result in bodily harm or damage to equipment. Prohibited Important to read and understand at all times Do not disassemble Any change or modification not expressly approved by designated qualified personnel could void your authority to operate this device. Always make sure that the disc does not have a crack before use. If the disc has a crack (especially around the center hole), it is recommended to make a copy immediately and use the copy instead. When a cracked disc is used continuously, the size of the crack is likely to grow and this will eventually result in irreparable damage to the disc. [. . . ] For Windows98/2000/ME/XP/NT4. 0 or higher version that uses a device driver provided by Windows, there is no need to set up an extra device driver. Refer to the steps below to see if Windows detects the drive. Double-click on the My Computer icon on your desktop. Double-click on the Control Panel folder. The TSST CD-RW TS - *** device name is displayed. . Setup Connecting the Cables Setting Up the Device Driver Automatic Setup The device driver is located in the Ddriver folder of the CD Record Utility disc which is provided in the package. Insert the CD Record Utility disc into the CD-ROM drive and open the Ddriver folder. Run the CDSETUP. EXE file in the Ddriver folder. When Setup is successfully completed, click OK button or press the Enter key. Reboot the computer. Manual Setup Make the C:\LG directory. Copy the files from the diskette to the C:\LG directory. Select a desired mode from a program window, and click "Setup" The reading speed of a drive operates in a selected mode. Close the program window by selecting "Close". At this time, the reading speed will keep operating by the changed speed unless you would change a mode and would end a program. It is recommended to use a "Maximum Speed Mode" when operating a Data Copy & a Disc Copy and to use a "Low Noise Mode" when operating a general operation. Other Function How to deactivate the automatic operation: This program automatically runs when PC is booting up. If you wish to deactivate the automatic operation, deactivate the selected Automatic Operation item in the tray (or task tray) menu. Place to download a MAGIC SPEED Samsung's Customer Service Homepage (URL:www. samsungODD. com) - Select a Firmware > MAGIC SPEED. Using the Drive Connecting the Cables Upgrading the Firmware Flash Memory The product firmware can be upgraded by downloading the updated file from the following Web site: Http://samsung-ODD. com Http://samsung. com Using the Drive Connecting the Cables System Requirements Before you install the CD-RW Drive, we strongly recommend that you check that your setup meets the system requirements listed below. Item Computer Disk space Windows version Description Intel Pentium II 400MHz(or higher), 64 MB of RAM (or higher) with an 40pin IDE interface for Ultra DMA. At least twice as much free space as the amount of data to be writable. Windows 98/2000/ME/XP/NT4. 0 (or higher) Troubleshootin Connecting the Cables Hard Drive Network Drive CD-ROM Drive If you have any problems recording via your CD-RW Drive, follow the appropriate instructions below for the source that you are using. Hard Drive Check whether the source file is corrupted. Optimize the hard disk by using the Windows defragmenter feature: START / PROGRAMS / ACCESSORIES / SYSTEM TOOLS / DISC DEFRAGMENTER Decompress the hard disk if it is compressed. Make sure that the space available on the hard disk is at least twice the size of the largest file to be recorded on the disc. [. . . ] + Click OK + Restart your PC + Expand the CD-ROM icon Windows 2000/XP Select the DMA mode by selecting [Start > Setting > Control Panel > System > Device Manager > IDEATA/ATAPI Controller > Default/Assistant IDE Channel Advanced Information] Troubleshootin Problem The CD-RW Drive is not detected by the computer. Connecting the Cables Meaning / Solution Check that the power, audio and IDE cables are correctly connected to the computer. Change the IDE cable and reconnect it to the computer. Preferably, connect a second IDE cable to the CD-RW drive in master mode. Check the position of the jumper in the master/slave select terminal. After installing the CD-RW Drive, the PC gets slower. The CD-RW Drive is not recognized by MS-DOS. Reinstall the device driver or update it with the latest version by downloading it from the Samsung Web site. [. . . ]