User manual LG M1717S

[. . . ] If the power cable is faulty in any way, please contact the manufacturer or the nearest authorized repair service provider for a replacement. The power supply cord is used as the main disconnection device. Ensure that the socket-outlet is easily accessible after installation. Operate the display only from a power source indicated in the specifications of this manual or listed on the display. [. . . ] The product may fall and get damaged or injure your foot. Positioning your display After installation, adjust the angle as shown below. 1. Adjust the position of the panel in various ways for maximum comfort. Tilt Range : -6°~22° -6 22 When adjusting the angle of the screen, do not put your finger(s) in between the head of the monitor and the stand body. You can hurt your finger(s). 6 Connecting the Display Swivel Range : 350° 350 Height Range : maximum 3. 94 inches (100. 0 mm) 100. 0 mm * Please be sure to remove the Locking pin to adjust the height. WARNING You do not need to replace the Locking pin after it is removed, to adjust its height. ERGONOMIC It is recommended that in order to maintain an ergonomic and comfortable viewing position, the forward tilt angle of the monitor should not exceed 5 degrees. 7 Connecting the Display Using the Pivot function -The pivot function allows you to rotate the screen 90 degrees clockwise. 1. Lift the monitor to its highest height to utilize the Pivot function. Landscape & Portrait : You can rotate the panel 90 o clockwise. Please be cautious and avoid contact between the monitor head and the Stand Base when rotating the screen to access the Pivot function. If the monitor head touches the Stand Base, then the Stand Base could crack. Head section Stand section 3. Be careful with the cables when rotating the screen. 8 Connecting the Display Connecting with the PC/AV equipment 1. Before setting up the monitor, ensure that the power to the monitor, the computer 2. Connect signal input cable 1 A Connect DVI-I Cable B Connect DVI-D Cable C Connect HDMI Cable system, and other attached devices is turned off. and power cord of the signal cable. 2 in order, then tighten the screw NOTE This is a simplified representation of the rear view. This rear view represents a general model; your display may differ from the view as shown. Press the MENU Button once to return to the main menu to select another function. Press the MENU Button twice to exit from the OSD. 17 On Screen Display(OSD) Selection and Adjustment The following table indicates all the On Screen Display control, adjustment, and setting menus. DVI-I(A) : DVI-I(Analog) signal DVI-I(D) : DVI-I(Digital) signal DVI-D : DVI-D(Digital) signal HDMI(Y) : HDMI (YUV) signal HDMI(R) : HDMI (RGB) signal Main menu Sub-menu CUSTOM Supported signals DVI-I(A) DVI-I(D) DVI-D HDMI(Y) HDMI(R) DVI-I(A) DVI-I(D) DVI-D HDMI(R) DVI-I(A) DVI-I(D) DVI-D HDMI(R) DVI-I(A) DVI-I(D) DVI-D Description The default mode that adjusts the overall range of colors of the RGB LED panel. COLOR MODE sRGB Adjusts colors based on sRGB. ADOBE RGB Adjusts colors based on ADOBE RGB. CALIBRATION Adjusts Color features by controlling the Brightness, WhitePoint and Gamma values through the color management system (CMS). Adjusts Color features by controlling the Brightness, WhitePoint , RGB Color Gamut and Gamma values through the color management system (CMS). EMULATION DVI-I(A) DVI-I(D) DVI-D PICTURE BRIGHTNESS CONTRAST GAMMA BLACK LEVEL WHITE BALANCE DVI-I(A) DVI-I(D) DVI-D HDMI(Y) HDMI(R) HDMI(Y) HDMI(R) DVI-I(A) Standard image settings. 18 On Screen Display(OSD) Selection and Adjustment COLOR COLOR TEMP (PRESET) 5000K 6500K 7200K 8200K 9300K DVI-I(A) DVI-I(D) DVI-D HDMI(Y) HDMI(R) Color temperature adjustments (USER) RED GREEN BLUE HUE SATURATION SIX COLOR (RED/GREEN/ BLUE/CYAN/ MAGENTA/ YELLOW) COLOR RESET TRACKING HORIZONTAL VERTICAL CLOCK PHASE SHARPNESS DVI-I(A) Adjusts the position of the screen Adjusts the clarity and stability of the screen DVI-I(A) DVI-I(A) DVI-I(D) DVI-D HDMI(Y) HDMI(R) SETUP LANGUAGE OSD POSITION (HORIZONTAL / VERTICAL) DVI-I(A) DVI-I(D) DVI-D HDMI(Y) HDMI(R) HDMI(Y) HDMI(R) Additional settings OVERSCAN ARC RTC POWER INDICATOR FACTORY RESET DVI-I(A) DVI-I(D) DVI-D HDMI(Y) HDMI(R) NOTE The order of icons may differ depending on the model (18~27). 19 On Screen Display(OSD) Selection and Adjustment The OSD screen will appear when you press the MODE button on the front of the monitor. DVI Input HDMI(RGB) Input HDMI(YUV) Input *When HDMI(RGB) is inputted, CUSTOM, sRGB and ADOBE RGB mode is supported. *When HDMI(YUV) is inputted, only CUSTOM is supported. MENU : Exit : Move AUTO/SET : Select Main menu CUSTOM Description The default mode that adjusts the overall range of colors of the RGB LED panel. You can adjust the color functions of the main menu. * In modes other than CUSTOM mode, you cannot adjust the PICTRUE (CONTRAST, GAMMA) and COLOR functions of the main menu. sRGB Color features are set for sRGB specification. Color Temperature, Brightness, Gamma and x and y coordinates of RGBCMY are adjusted based on the sRGB specification. 20 On Screen Display(OSD) Selection and Adjustment Main menu ADOBE RGB Description Color features are set for Adobe RGB specification. Color Temperature, Brightness, Gamma and x and y coordinates of RGBCMY are adjusted based on the Adobe RGB specification. CALIBRATION Adjusts Color features by controlling the Brightness, WhitePoint and Gamma values through the color management system (CMS). * This function is available only after 'True Color Finder' is installed on the computer and calibration has been performed with the calibrator. EMULATION Adjusts Color features by controlling the Brightness, WhitePoint , RGB Color Gamut and Gamma values through the color management system (CMS). * This function is available only after 'True Color Finder' is installed on the computer and calibration has been performed with the calibrator. 21 On Screen Display(OSD) Selection and Adjustment You were introduced to the procedure of selecting and adjusting an item using the OSD system. [. . . ] If yes, readjust the video card to the recommend resolution. If the recommended resolution (optimal resolution) is not selected, letters may be blurred and the screen may be dimmed, truncated or biased. Make sure to select the recommend resolution. The setting method can differ by computer and O/S (Operation System), and resolution mentioned above may not be supported by the video card performance. [. . . ]