User manual LG M2762D

[. . . ] ENGLISH OWNER'S MANUAL MONITOR TV Please read this manual carefully before operating your set and retain it for future reference. MONITOR TV MODELS M1962D M2062D M2262D M2362D M2762D www. lge. com PREPARATION FRONT PANEL CONTROLS I This is a simplified representation of the front panel. The image shown may be somewhat different from your set. Headphone Jack IR receiver (Remote controller receiver) Power Indicator illuminates blue when the set is switched on. Note:You can adjust Power indicator in the OPTION menu. INPUT Button OK VOLUME PROGRAMME Power MENU Buttons Button Button Buttons Button INPUT MENU OK VOL PR Light Sensor This is lens for light sensor select outside luminance, when setting AUTO BRIGHT ON. 1 PREPARATION BACK PANEL INFORMATION I This is a simplified representation of the back panel. [. . . ] · Press the RETURN button to move to the previous menu screen. G G is a trademark of SRS Labs, Inc. TruSurround HD technology is incorporated under license from SRS Labs, Inc. 68 SOUND CONTROL AUDIO RESET Settings of the selected Sound Mode return to the default factory settings. AUDIO D Move OK R AUDIO Balance D Move OK R Balance Sound Mode : Standard 0 L 0 L Sound Mode : Standard · SRS TruSurround HD : Off · Treble · Bass · Reset t Rese : PCM : On Digital Audio Out TV Speaker E · SRS TruSurround HD : Off · Treble · Bass · Reset t Rese Digital Audio Out TV Speaker E 50 50 50 50 i Resetting sound mode configuration. . . : PCM : On 1MENU 2 OK Select A U D I O. Select R e s e t. 3 OK Initialize the adjusted value. · Press the MENU or EXIT button to close the menu window. · Press the RETURN button to move to the previous menu screen. 69 SOUND CONTROL SELECTING DIGITAL AUDIO OUT This function allows you to select your preferred Digital Audio Output. The TV can only output DOLBY Digital if a channel is broadcast with Dolby Digital audio. When Dolby digital is available, selecting Auto in the Digital Audio Out menu will set SPDIF(Sony Philips Digital InterFace) output to Dolby Digital. If Auto is selected in the digital audio out menu when dolby digital is not available, SPDIF output will be PCM(Pulsecode modulation). Even if both Auto and Audio language have been set in a channel which broadcast Dolby Digital Audio, only Dolby Digital will be played. If the sample rate converter on this chip does not support 44. 1 to 48kHz, this content should always produce stereo PCM at digital output. AUDIO D Move OK R AUDIO D Move OK R Balance Sound Mode : Standard 0 L Balance Sound Mode : Standard 0 L · SRS TruSurround HD : Off · Treble · Bass · Reset D i g i t Audio i o Digital a l A u dOutO u t TV Speaker E · SRS TruSurround HD : Off · Treble · Bass · Reset D i g i t Audio i o Digital a l A u dOutO u t TV Speaker E 50 50 :: PCM PCM : On 50 50 :: PCM PCM : On Auto PCM PCM 1MENU 2 OK Select A U D I O. Select D i g i t a l A u d i o O u t. 3 OK Select A u t o or P C M. Manufactured under license from Dolby Laboratories. "Dolby "and the double-D symbol are trademarks of Dolby Laboratories. · There is a possibility that when HDMI mode, some DVD players do not make SPDIF sound. At that time, set the output of the digital audio of the DVD player to PCM. · Press the MENU or EXIT button to close the menu window. · Press the RETURN button to move to the previous menu screen. 70 SOUND CONTROL TV SPEAKERS ON/ OFF SETUP You can adjust the internal speaker status. In TV, AV, COMPONENT, HDMI, RGB, DVI mode the TV speaker can be operational even though when there is no video signal. If you wish to use an external Hi-Fi system, turn off the TV internal speakers. AUDIO D Move OK R AUDIO D Move OK R Balance Sound Mode : Standard 0 L Balance Sound Mode : Standard 0 L · SRS TruSurround HD : Off · Treble · Bass · Reset Digital Audio Out T Speak TVVSpeaker e r E · SRS TruSurround HD : Off · Treble · Bass · Reset Digital Audio Out T Speak TVVSpeaker e r E 50 50 : PCM O : :On n 50 50 : PCM O : :On n Off On On 1MENU 2 OK Select A U D I O. Select T V S p e a k e r. 3 OK Select O n or O f f. · Press the MENU or EXIT button to close the menu window. · Press the RETURN button to move to the previous menu screen. 71 SOUND CONTROL AUDIO DESCRIPTION(IN DIGITAL MODE ONLY) This function is for the blind, and provides explanatory audio describing the current situation in a TV programme in addition to the basic audio. When Audio Description On is selected, basic audio and Audio Description are provided only for those programmes that have Audio Description included. When Main Audio is AAC or Dolby Digital Plus Audio, Audio Description is not supported. AUDIO D Move OK AUDIO D Move OK · SRS TruSurround HD : Off · Treble · Bass · Reset Digital Audio Out TV Speaker Audio Description Audio Description : PCM : On On :: On · Volume 50 TV Speaker 50 50 · SRS TruSurround HD : Off · Treble · Bass · Reset Digital Audio Out Audio Description Audio Description : PCM : On On :: On Off On · Volume 50 On 50 50 1MENU 2 OK Select A U D I O. Select A u d i o D e s c r i p t i o n. 3 OK Select O n or O f f. When the A u d i o D e s c r i p t i o n is selected O n, 4 OK Select the desired V o l u m e. · Press the MENU or EXIT button to close the menu window. · Press the RETURN button to move to the previous menu screen. 72 SOUND CONTROL I/II Stereo/Dual Reception (In Analogue Mode Only) When a programme is selected, the sound information for the station appears after the programme number and station name disappear. I/II Select the sound output. Broadcast Mono Stereo Dual On Screen Display MONO STEREO DUAL I, DUAL II, DUAL I+II A Mono sound selection If the stereo signal is weak in stereo reception, you can switch to mono. In mono reception, the clarity of sound is improved. Language selection for dual language broadcast If a programme can be received in two languages (dual language), you can switch to DUAL I, DUAL II or DUAL I+II. DUAL I DUAL II DUAL I+II A Sends the primary broadcast language to the loudspeakers. Sends the secondary broadcast language to the loudspeakers. [. . . ] Ack [k][ ][Set ID][ ][OK/NG][Data][x] You can also adjust bass in the AUDIO menu. In case that SRS TruSurround HD is `On', it doesn't operate and is fixed to 50. No operation at USB input Transmission [k][s][ ][Set ID][ ][Data][Cr] 11. OSD Select (Command: k l) G To select OSD (On Screen Display) on/off when controlling remotely. Data Min : 00 ~ Max : 64 * Refer to `Real data mapping'. [. . . ]