User manual LG MG-583MC

[. . . ] If the power cable is faulty in any way, please contact the manufacturer or the nearest authorized repair service provider for a replacement. The power supply cord is used as the main disconnection device. Ensure that the socket-outlet is easily accessible after installation. Operate the display only from a power source indicated in the specifications of this manual or listed on the display. [. . . ] Thank for selecting LGE products !!! Please make sure the following items are included with your monitor. If any items are missing, contact your dealer. User's Guide/Cards 15-pin D-Sub Signal Cable (To set it up, this signal cable may be attached to this product before shipping out. ) Or Power Cord AC-DC adapter (Depending on the country) AC-DC adapter (Depending on the country) DVI-D Signal Cable (This feature is not available in all countries. ) NOTE This accessories may look different from those shown here. User must use shielded signal interface cables (D-sub 15 pin cable, DVI-D cable) with ferrite cores to maintain standard compliance for the product. 4 Connecting the Display Before setting up the monitor, ensure that the power to the monitor, the computer system, and other attached devices is turned off. 1 way stand 1. Place the monitor with its front facing downward on a soft cloth. 2. Use a coin on the back of the stand base and turn the screw clockwise to tighten. 3. Once assembled take the monitor up carefully and face the front side. When you desire to disintegrate the monitor from the stand base, use a coin to turn the screw counterclockwise. Important This illustration depicts the general model of connection. Your monitor may differ from the items shown in the picture. Do not carry the product upside down holding only the stand base. The product may fall and get damaged or injure your foot. 5 Connecting the Display Before setting up the monitor, ensure that the power to the monitor, the computer system, and other attached devices is turned off. 2 way stand 1. Place the monitor with its front facing downward on a soft cloth. 2. You can unlock the OSD controls at any time by pushing the MENU button for several seconds. The message "OSD UNLOCKED" should appear. SMART+ Button Use this button to enter AUTO BRIGHT, ORIGINAL RATIO, DUAL WEB, CINEMA MODE menus. For more information, refer to page 19~21. ENGINE Button For more information, refer to page 22~23. 11 Control Panel Functions AUTO Button AUTO IMAGE ADJUSTMENT When adjusting your display settings, always press the AUTO button before entering the On Screen Display(OSD). (Only Analog Mode) This will automatically adjust your display image to the ideal settings for the current screen resolution size (display mode). The best display mode is E1950T : 1360 x 768 E2050T : 1600 x 900 E2250T : 1920 x 1080 MG-583MC : 1920 x 1080 INPUT Button (SOURCE Hot key) Use this button to select source from input. When two input signals are connected, you can select the input signal (D-SUB/DVI) you want. When only one signal is connected, it is automatically detected. The default setting is D-Sub. EXIT Button Exit the OSD(On Screen Display). Power Button & Power Indicator Use this button to turn the display on or off. From front view, the power indicator stays purple if the display is running properly (On Mode). If the display is in Sleep Mode (Energy Saving), the power indicator is blinking purple. Light Sensor This is lens for light sensor detect outside luminance, when setting AUTO BRIGHT ON. 12 On Screen Display (OSD) Control Adjustment Screen Adjustment Making adjustments to the image size, position and operating parameters of the display is quick and easy with the On Screen Display Control system. A short example is given below to familiarize you with the use of the controls. [. . . ] · Check Control Panel --> Display --> Settings and adjust the display to the recommended resolution or adjust the display image to the ideal setting. Set the color setting higher than 24 bits (true color). G Any horizontal noise appearing in any image or characters are not clearly portrayed. IMPORTANT Check Control Panel --> Display --> Settings and see if the frequency or the resolution were changed. If yes, readjust the video card to the recommend resolution. If the recommended resolution (optimal resolution) is not selected, letters may be blurred and the screen may be dimmed, truncated or biased. [. . . ]