User manual LG R500-UPCIT

[. . . ] Instead, they are requested to directly contact a designated service center or the outlet at which the product was purchased. x Never spill any kind of liquid into the unit. Should this happen, unplug or main switch off the unit and contact an authorized service center. x Do not insert anything between the air outlet blades because the inner fan may be damaged and could cause injury. [. . . ] The air conditioner runs in the Energy saving mode, It will run at +2C of the standard temperature. The outer air flow blade moves up and down. To stop the Energy saving mode, press the button again. 4 To adjust the temperature, press button once or more times to get the required temperature. The scope of the temperature adjust should between standard temperature +2C and -2C E-9 Cooling Your Room You must select the Cool mode if you wish to adjust the: x Cooling temperature x Fan speed when cooling 1 If necessary, press the Result: (On/Off) button. x The operation indicator on the indoor unit lights up. x The air conditioner starts up in the mode selected when the unit was last used. The air conditioner is fitted with a protection mechanism to prevent the unit from being damaged when it is started immediately after being: x Plugged in x Stopped lt will start up normally after three minutes. IMPORTANT 2 If the is not displayed at the top of the remote control, press the button on the remote control one or more times until it appears. Result: x The indoor unit beeps each time you press the x The air conditioner runs in COOL mode. button. Note 3 To adjust the temperature, press the button one or more times until the required temperature is displayed. Possible temperatures are between 18C and 30C inclusive. Result: x Each time you press the button: - The temperature is adjusted by 1C - The indoor unit beeps x The air conditioner starts cooling, provided that the room temperature is higher than the selected temperature. x If the room temperature reaches the set temperature, the air conditioner stops cooling, but the fan is still operating. 4 Select the fan speed by pressing the until the required setting is displayed: Automatic (rotated : Low Medium High Result: Each time you press the beeps. button one or more times ) button, the indoor unit 5 To control the direction of the air flow, refer to pages 16 and 17. E-10 Changing the Room Temperature Quickly ENGLISH The Turbo cooling function is used to cool your room as quickly as possible. Example : You have just come home and find that the room is very hot. The blade move up and down, around the base position set. 3 To stop the blade moving up and down, press the button again. Note If you switch the air conditioner. . . Set to the initial position powered. E-16 Adjusting the Air Flow Direction Horizontally ENGLISH There are two sets of inner air flow blades. Just as the outer air flow blade can be adjusted vertically, the inner blades can be adjusted horizontally. 1 Adjust each set of inner blades to the required position, by pushing or pulling them sideways. E-17 Setting the On Timer The On Timer enables you to switch on the air conditioner automatically after a given period of time. You can set the period of time from 30 minutes to 24 hours. 1 To set the operating time, press the button one or more times until the required time is displayed. Possible time is between 0. 5 hour and 24 hours inclusive. 2 Press the Result: (Set/Cancel) button to complete the setting. x Blinking of the timer indicator stops. x The selected mode and the temperature on the display disappear after 10 seconds. x The air conditioner will switch on automatically when the counter displayed on the remote control reaches the set time and disappears the On timer setting. 3 To select an operating mode in advance, press the button until the desired mode is displayed at the top of the remote control. Result: x The air conditioner will run in the selected mode when it is turned on. To Cancel the On Timer Press the Note (Set/Cancel) button. [. . . ] The automatic protection feature may be triggered and the air conditioner stopped. A water leak or some other malfunction may occur if the heat exchanger freezes. Water may condense on and drip from the surface of the indoor unit if it is used for long periods. Indoor Humidity 80% or less - Outdoor Temperature 21C to 43C approx. [. . . ]