User manual LIEBHERR WKES 4552 GRANDCRU

[. . . ] - Avoid positioning the appliance in direct sunlight or near cookers, radiators or similar sources of heat. - The energy consumption depends on the installation conditions, e. g. - Keep the time the appliance is open to a minimum. Accumulated dust increases the energy consumption: - Once a year, dust the refrigerating unit together with the metal grid of the heat exchanger at the back of the appliance. Saving energy Description of the appliance Lock Operating and control elements Interior light (LED light strip) Note Fit the short grid shelf in the top position only. Grid shelves Activated charcoal filter Type plate 12 Adjustable- height feet • To prevent injury or damage to the unit, the appliance should be unpacked and set up by two people. Safety instructions and warnings • In the event that the appliance is damaged on delivery, contact the supplier immediately before connecting to the mains. [. . . ] • If you have a lockable appliance, do not keep the key near the appliance or within reach of children. Appliance dimensions WKt 4551 WKt 5551 A = 1650 mm A = 1920 mm • The appliance is designed for use in enclosed areas. Do not operate the appliance outdoors or in areas where it is exposed to splash water or damp conditions. • The LED light strip illuminates the interior of the appliance. • When transporting or operating the appliance at an altitude of more than 1500 m above sea level, the glass pane in the door can break due to the reduction in air pressure. Broken fragments are sharp-edged and can cause serious injury. Only operate the appliance with alternating current (AC). The permissible voltage and frequency are indicated on the type plate. The position of the type plate is shown in the section entitled Description of the appliance. The socket must be properly earthed and protected by a fuse. The tripping current of the fuse must be between 10 A and 16 A. The socket must not be situated behind the appliance and must be easily accessible. Do not connect the appliance using an extension cable or extension socket. Do not use stand-alone inverters (conversion of direct current to alternating/three-phase current) or energy-saving plugs. Switching off Hold down the Alarm button and then press the Light button. Note If the appliance is operated in a low ambient temperature, the fan may also run when the fan function is deactivated. Fan switch If you are storing wine for long periods of time, it should be stored at a temperature of between 10°C and 14°C. Storing wine This is the temperature wine cellars are kept at, and it is just right to allow wine to mature properly. The following drinking temperatures are recommended for the various types of wine. Red wines: +14°C to +18°C Rosé wines: +10°C to +12°C White wines: +8°C to +12°C Sparkling wines, Prosecco: +7°C to +9°C Champagne: +5°C to +7°C 14 In set-up mode you can set the child lock and adjust the brightness of the display. The child lock is designed to protect the appliance from being switched off accidentally. Additional functions GB Adjusting the display brightness Press for 5 seconds. Display = Activating the child lock Press for 5 seconds. Display = Display = Display = Display = Display = Use buttons and to select the desired setting. Display = h1 = minimum brightness h5 = maximum brightness Display = Display = Display = Deactivating the child lock Press for 5 seconds. Display = The adjusted brightness will be activated after one minute. Note If a button is pressed, the display lights up for one minute at maximum brightness. Display = Display = Demo mode can be activated for presenting the appliance at exhibitions or in salesrooms as though in normal operating mode. If this mode is activated by accident, it can be deactivated as detailed below. When in this mode, the cooling circuit is switched off! Demo mode Display = Display = Display = Display = The refrigeration unit switches on. [. . . ] 9. Transfer door handle and plugs to the opposite side. 5. Release cover with a small screwdriver and remove. 5 10 10. Push on pressure plates until they engage. 18 GB 11 16 11 17 16. Slide cover (with the smaller opening) from outside to inside and click into place. 11. Release covers on the inside, slide them towards the outside and remove. 17. Guide cover with the larger opening over the hinge bracket, slide it from outside to inside and click into place. 12 18 13 12. Unscrew hinge bracket. 13. Unscrew closing bracket. 18. Undo adjustable foot with the spanner provided. 14 19 19. Pull hinge pin upwards and unscrew it from the adjustable foot. 20. Pull adjustable foot downwards to remove. 20 14. Re-fit closing bracket on the opposite side. 15 15. Re-fit hinge bracket on the opposite side. Insert screws in the marked openings. 22 21 21. Unscrew hinge bracket. 22. Transfer cover to the opposite side. 19 23 27. Place door on pin and move the top of it to the hinge bracket. [. . . ]