User manual LIFT-MASTER 422LM

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual LIFT-MASTER 422LM. We hope that this LIFT-MASTER 422LM user guide will be useful to you.

Lastmanuals help download the user guide LIFT-MASTER 422LM.


Mode d'emploi LIFT-MASTER 422LM
Download
Manual abstract: user guide LIFT-MASTER 422LM

Detailed instructions for use are in the User's Guide.

[. . . ] When doing so please follow the installation and safety instructions. The built-in time switch offers you additional facilities: You can program daily opening and closing times for your roller shutters. INITIAL CONFIGURATION Each device is set with a different default radio identification code. The first time it is connected to the power supply, or after it has been switched off for an extended period of time, the timer will operate as follows: the text "AUTO" will appear at the top of the display (in reference to the operating mode; see paragraph "Operating Description"), while the time (12:00; the default value) and the number "1" (in the bottom left-hand corner) both start to flash. [. . . ] Operation Programming days of the week and times Press and hold the STOP (MODE) button for at least 2 seconds: the day of the week will flash at the bottom of the display (as is usually the case, 1 = Monday, 2 = Tuesday, etc. ); the hours and minutes also appear (every time the unit is reset or after it has been switched off for an extended period of time, the time is set to the default value of 12:00), along with a small clock symbol. The day of the week and the current time (in the 0:00 ­ 23:00 format) are programmed in this phase. Scroll through the days of the week using the UP and DOWN buttons. The number corresponding to the selected day flashes at the bottom of the display; press the STOP (MODE) button to set the desired day. At this point the hour digits begin flashing on the display; set the cor- Rect value using the UP and DOWN buttons and press the STOP (MODE) button to confirm; the minute digits then start to flash: use the UP and DOWN buttons to set the correct value and press STOP (MODE) to confirm. At this point you will enter the programming phase for the times at which the automatic commands will be transmitted every day of the week. The default setting for the UP command, every day of the week, is 7:00, while the DOWN command default time is set to 21:00. Where the clock symbol had appeared previously at the bottom of the display, there will now be a P and the number 1 (Monday). An arrow pointing upwards will also appear next to the P, to indicate that the UP command for Monday must be programmed and the hour digits will flash: select the desired hour value for the UP command and confirm using the STOP (MODE) button. Then immediately press the UP button on the remote control and hold it until 1x peep is heard. 422LM and hold it until first 2x peeps and then 4x peeps are heard. SETTING STANDARD TIME/DAYLIGHT SAVING TIME To move from daylight saving time to standard time and vice-versa, depending on the time of year, press and hold the UP and DOWN buttons simultaneously for approximately 2 seconds: the schedule displayed will be delayed by one hour. If you press and hold the UP and DOWN buttons simultaneously for approximately 2 seconds, the current schedule will move forward one hour in relation to the initial schedule. Example: it is 12:00; if you press UP and DOWN simultaneously once the time will switch to 13:00. If you press UP and DOWN simultaneously again, the time will be set to 11:00. pressing UP and DOWN simultaneously once again will restore the time to 12:00 and the cycle will start all over again. FOR THE INSTALLER - IMPORTANT - The timer is not equipped with a sectioning device. This means that in certain conditions the signal may not reach the receiver. Take this into account in critical applications. [. . . ] Reset To reset the programmed data, press the corresponding button, which is located underneath the DOWN button and can be seen once the front panel has been removed. this will restore all the default settings. Settings will also be reset if you disconnect the power supply for approx 1 minute. Chamberlain warrants to the first retail purchaser of this product that the product shall be free from any defect in materials and/or workmanship for a period of 24 full months (2 years) from the date of purchase. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE LIFT-MASTER 422LM

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets...
In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.

Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual LIFT-MASTER 422LM will begin.

Search for a user manual

 

Copyright © 2015 - LastManuals - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.

flag